Related Manuals for 3M 8100CB
Summary of Contents for 3M 8100CB
- Page 1 Operator’s Guide …with copyboard 8100CB …interactive whiteboard 8200IW …deluxe interactive whiteboard 8200IC July 2003 78-6970-9185-4 Rev. A Copyright © 2003, 3M. All Rights Reserved.
- Page 2 (This page intentionally left blank for printed version)
-
Page 3: Table Of Contents
3M™ Digital WallDisplay Contents Introduction Thank You for Choosing 3M ............5 Intended Use . - Page 4 Contents Onscreen Messages ............. . .40 eBeam Software .
-
Page 5: Thank You For Choosing 3M
3M™ Digital WallDisplay Introduction Thank You for Choosing 3M Thank you for choosing 3M equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come. For optimum performance, please follow the operating instructions carefully. - Page 6 Introduction Safety Precautions • To reduce the risk of electric shock, do not disassemble this appliance. Request a qualified technician when service or repair work is required. Incorrect reassembly can cause electric shock when the appliance is subsequently used. • Connect this appliance to a grounded outlet. •...
-
Page 7: Product Safety Label
3M™ Digital WallDisplay Product Safety Label The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring your attention. Wall Display Save These Instructions The information contained in this manual will help you operate and maintain your 3M Digital WallDisplay. In some countries, the voltage is NOT stable. -
Page 8: Trademarks
Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the U.S. and other countries. Digital Light Processing is a trademark or registered trademark of Texas Instruments. eBeam, e-Beam, eBeam Mouse, eBeam Moderator, eBeam Software, ImagePort and eBeam Presenter are regis- tered trademarks of Electronics for Imaging, Inc. -
Page 9: Fcc Statement-Class A
3M™ Digital WallDisplay FCC Statement—Class A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 10: Model Identification And Differences
8000DP 3M Digital WallDisplay 8000DP for Projection Display 8000VC 3M Digital WallDisplay 8000VC for Video Teleconferencing 8100CB 3M Digital WallDisplay 8100CB with Copyboard Display 8200IC 3M Digital WallDisplay 8200IC with Interactive Collaboration 8200IW 3M Digital WallDisplay 8200IW with Interactive Whiteboard Model Differences Below is a table that identifies the differences between the 3M Digital WallDisplay models. -
Page 11: Contents
3M™ Digital WallDisplay Contents The 3M Digital WallDisplay (3M DWD) is shipped with the necessary cables required for standard VCR, PC, Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any are missing, please contact your place of purchase. POWER MOUSE MENU... -
Page 12: Part Identification
Introduction Part Identification OWER MOUSE MENU MUTE BLANK IN UT Wall Display 1. Facade 2. Lamp Housing Door (behind facade) 3. Projection Screen 4. Left Bezel 5. Remote Control Unit 6. Storage Door 7. Storage Door Window 8. On/Off Button 9. -
Page 13: 3M Digital Wall Display Features
3M™ Digital WallDisplay 3M Digital Wall Display Features The 3M Digital WallDisplay combines the following features into one sleek, sophisticated package. • Full connectivity for computer or video presentations • Large 60˝ diagonal screen • 4:3 screen aspect ratio matches business applications and viewing data •... -
Page 14: System Setup
Connects to a control device’s serial port and provides control of the 3M Digital WallDisplay using RS-232C protocol and the specified serial commands. *Available only on 3M DWD 8100CB and 8200IC **Available only on 3M DWD 8200IC and 8200IW A U D IO... -
Page 15: Operation
3M™ Digital WallDisplay Operation Startup 1. Plug power cord into wall socket. 2. Flip on the Master Power Switch beneath the lower left corner of the 3M Digital WallDisplay, near the 3M label. This should stay on at all times. Now the 3M Digital WallDisplay is in standby mode. The large oval On/Off Button will be backlit amber after several seconds. -
Page 16: Shutdown
Operation Shutdown Press the On/Off Button on the bottom center panel of the 3M Digital WallDisplay unit. The lamp will turn off and the projector arm will return to its housing. The On/Off Button will flash amber as the arm closes. Note: There is a 30-second reset period before the On/Off Button will function again. -
Page 17: Remote Control Unit
3M™ Digital WallDisplay Remote Control Unit Features The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between the sensor and remote control must be shorter than 4 meters (13 feet). The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is beneath the cover. - Page 18 Remote Control Unit Forward Keypad Power Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will automatically extend the projection arm and ignite the lamp. Mute Press to temporarily turn off the sound. Press again or press the Volume + or - buttons to restore sound. Disk Pad Press to: •...
-
Page 19: Rear Keypad
3M™ Digital WallDisplay Rear Keypad Pointer Press to turn the pointing function on/off. A green dot will appear on the screen. The dot can be controlled by pressing the arrows on the Disk Pad. Volume Press the + button to increase or the - button to decrease the speaker loudness level. When the audio is muted, the Volume + or - buttons will also cancel the Mute function. -
Page 20: Installing Or Replacing Batteries
Remote Control Unit 3M™ Digital WallDisplay Installing or Replacing Batteries 1. Push and slide the battery compartment tab in the direction shown, then lift it off. 2. Install two AAA batteries as indicated by the diagram inside the compartment. 3. Snap the battery compartment cover back on. Note: Avoid excessive heat and humidity. -
Page 21: Digital Markers And Eraser
3M™ Digital WallDisplay Digital Markers and Eraser Assembling Digital Markers The 3M Digital WallDisplay recognizes dry-erase marker writing by signalling the marker’s exact location to the bezel. These signals are created and transmitted by small sensors near the ends of the battery-powered marker sleeves. -
Page 22: Assembling Digital Eraser
Digital Markers and Eraser Assembling Digital Eraser The digital eraser erases marker input by sending signals from the digital eraser in the same way as the digital markers. The eraser sends an “erase” signal when you press the felt eraser against the 3M Digital WallDisplay screen. -
Page 23: Menu System
3M™ Digital WallDisplay Menu System Menu Navigation Most adjustments and settings are available in the main menu and sub-menus. To navigate and make adjustments, use the 3M Digital WallDisplay’s Menu Keypad button or the remote control’s Menu and Disk Pad buttons. MENU KEYPAD Colorful—Bright Slider The Colorful—Bright slider adjusts the brightness, contrast, and color saturation levels simultaneously. - Page 24 Menu System Warm—Cool Slider The Warm—Cool slider adjusts the color temperature. Move the slider toward Warm to achieve warmer, more reddish images. Move the slider toward Cool to achieve cooler, more bluish images. To adjust the Warm—Cool slider: 1. Open the menu system by pressing the remote control Menu button or any arrow on the Menu Keypad. 2.
- Page 25 3M™ Digital WallDisplay Mute Menu Function The Mute menu function turns the sound on and off. To turn the Mute menu function on: 1. Open the menu system by pressing the remote control Menu button or any arrow on the Menu Keypad. 2.
- Page 26 Menu System Input Select Menu The Input Select menu defines the displayed video source. When Input Select menu is selected, the current video source is shown. The Input options are: Computer (VGA Input), DVI-D, S-Video, Comp. Video (RCA Video Input), and No Signal. An Input option is available to select when an active video source is connected to the 3M Digital WallDisplay input connection.
- Page 27 3M™ Digital WallDisplay Image Adj Sub-Menu The Image Adjustment sub-menu adjusts the projected image settings for the VGA and DVI-D inputs. Use the Vertical Position and Horizontal Position sliders to reposition an image if portions are not visible. Use the Phase and Sync sliders to eliminate vertical banding and noise.
- Page 28 Menu System Tools Sub-Menu The Tools sub-menu provides access to the following settings and tools: Onscreen Timer Allows you to set a timer and display it onscreen. Language Selects which language to use for onscreen commands. (Default language is English.) It cycles between English, German, Spanish, Italian, and French. Auto Shutoff Will automatically turn off the 3M Digital WallDisplay within the time desired.
-
Page 29: Copyboard Mode
3M™ Digital WallDisplay WallDisplay as a Copyboard or Digital Whiteboard Copyboard Mode This mode lets the 3M Digital WallDisplay unit capture all the data from the screen and print it to a printer con- nected directly to the 3M Digital WallDisplay. No computer is needed to run this system. This mode should be used without projection. -
Page 30: Using Whiteboard Mode
WallDisplay as a Copyboard or Digital Whiteboard 3. Press the top bezel button to print. 4. Press the bottom bezel button to clear the page and any information stored in the buffer. Using Whiteboard Mode Top LED Light Legend COMMUNICATING WITH A PC (Solid amber) CONNECTION ERROR (Solid red) - Page 31 3M™ Digital WallDisplay Installing the Software Installing the eBeam Software for the 3M Digital WallDisplay is quick and easy. Just follow these steps below. Install for PC Computer 1. Insert the CD labeled 3M Digital WallDisplay Software and Documentation into the PC’s CD-ROM drive.
-
Page 32: Using Projection Mode
WallDisplay as a Copyboard or Digital Whiteboard Using Projection Mode Top LED Light Legend COMMUNICATING WITH A PC (Solid amber) CONNECTION ERROR (Solid red) 1. Turn on the 3M Digital WallDisplay unit and wait for image to appear on the screen. 2. -
Page 33: Maintenance
3M™ Digital WallDisplay Maintenance General Maintenance For general cleaning of the screen and exterior of the 3M Digital WallDisplay, use a damp cloth or dry clean- ing cloth such as the 3M High Performance Cleaning Cloth. Standard dry-erase cleaners may be used on the dry-eraseable screens, such as Sanford Expo Whiteboard ®... -
Page 34: Lamp Replacement
Maintenance Lamp Replacement To reduce the risk of electrical shock, always turn off the 3M Digital WARNING WallDisplay unit and disconnect power cord before changing lamp. 1. Turn the power off and disconnect the power cord from the outlet. 2. Allow approximately 45 minutes for the lamp to cool, if necessary. 3. - Page 35 3M™ Digital WallDisplay 5a. Hold down this receptacle with your left thumb and (5b) pull connectors out of the receptacle with other hand. 6. Push up the metal lever on the lower left side of the lamp cartridge. 7. Grasp the lamp cartridge and pull it straight back out of the lamp compartment.
- Page 36 Maintenance 9. Push down the metal lever on the left side of the lamp cartridge. 10. Reconnect black wires to the receptacle. 11. Close the lamp housing door and tighten the screw. 12. Align the slots and tabs of the right side of the facade and projection arm as shown, then snap firmly into place.
-
Page 37: Resetting Lamp Hours
3M™ Digital WallDisplay Resetting Lamp Hours Please do the following within 10 minutes of turning power on after you replace the lamp. 1. Press the Menu Keypad or the Menu button on the remote control and use the Disk Pad to scroll down to the Tools menu. -
Page 38: Replacing Projectionscreen
Maintenance Replacing ProjectionScreen Replacing the 3M Digital WallDisplay screen is very simple. 1. Turn off the 3M Digital WallDisplay and disconnect the power cord from the wall outlet. 2. Remove the right and left side bezels. There are two ways to remove it. Either snap it off or insert a screwdriver into the notch located on the sides of each bezel, near the top. -
Page 39: Troubleshooting
3M™ Digital WallDisplay Troubleshooting Common Problems and Solutions Symptom Cause Power cannot be The power cord is disconnected. turned on. The Master Power Switch is not turned on. The arm facade is not in place. No picture or The desired input source is not sound. -
Page 40: Onscreen Messages
Troubleshooting Common Problems and Solutions, continued Symptom Cause Desired input The input source is not active. A signal source cannot be must be present for the input to be detected. selected. The input device (e.g. computer, VHS player, etc.) is not turned on. The remote control is not facing the The remote remote control sensor. -
Page 41: Ebeam Software
3M™ Digital WallDisplay eBeam Software Troubleshooting provides solutions for known issues with the eBeam system. This section covers the Microsoft Windows versions of eBeam Software. ® ® eBeam Hardware Detection/Use Message “eBeam not found. Check connection cable and power supply.” (This message might appear at application startup, or during the... -
Page 42: Network Connection/Shared Meetings
Troubleshooting Network Connection/Shared Meetings Problem To share a meeting, the eBeam Hardware must be connected and detected.” (This message appears when you choose Shared Meeting.) Unable to share or join a meeting over the EFI meeting server. Using a cable modem or DSL and unable to share or join a meet- ing over the EFI meet-... -
Page 43: Writing/Data Capture
3M™ Digital WallDisplay Writing Data/Capture Problem eBeam Software states that Hardware the eBeam hardware is detected, but writ- ing does not appear in eBeam Software’s Meeting application Active Page. Software Software is missing Hardware many of the strokes written with the digital marker. - Page 44 Troubleshooting Writing Data/Capture continued Problem eBeam Digital marker strokes Software made at the bottom of the whiteboard do not appear in eBeam Software’s Meeting application. Digital eraser does Software not erase. Try the following: • Make sure you are writing within the calibrated image area on the whiteboard.
-
Page 45: Efi Meeting Applet
3M™ Digital WallDisplay EFI Meeting Applet Problem eBeam Applet does not load. Software While using iVISTA, Software the applet does not load. Unable to see shared Software meeting names in the Join Meeting dialog box. © 3M 2003. All Rights Reserved. Try the following: Microsoft Internet Explorer... -
Page 46: Background Images
Troubleshooting Background Images Problem eBeam Microsoft Excel ® ® Software spreadsheet did not load properly. Background image Software quality is bad. Try the following: • Is there a graph in the spreadsheet? eBeam Software’s Meeting application cannot import a spreadsheet containing a graph. -
Page 47: Service Information
3M™ Digital WallDisplay Service Information Parts and Accessories Description Power Cord (EU) Power Cord (US) Power Cord (UK) Serial Mouse Cable USB Cable VGA Cable DVI-D Cable PC Audio Cable S-Video Cable Replacement Lamp Kit Remote Control Unit Macintosh Adapter 3-Conductor Video/Audio Cable Dry-Erase Screen 3M Vikuiti High Brightness Screen... -
Page 48: Appendix
Appendix 3M™ Digital WallDisplay Specifications l i b y t i l i b f i l ˝ 0 ™ 1600 hours ˝ 6 ˝ 2 y t i l a i i n i 20 Watts per channel 3M™ Digital WallDisplay ˝... -
Page 49: Input/Output Signal Specifications
3M™ Digital WallDisplay Input/Output Signal Specifications Computer Compatibility Resolution Refresh Rate 640x400 640x480 640x480 640x480 640x480 800x600 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1024x768 1280x1024 © 3M 2003. All Rights Reserved. c i t Horizontal Frequency 85 Hz 37.9 kHz 60 Hz 31.5 kHz 72 Hz... -
Page 50: Printer Compatibility
Appendix Printer Compatibility Apollo P-2200 Fiery X2e HP Business Inkjet 2250TN HP Color LaserJet 4550 HP DeskJet 340 648C 842C 932C 952C 970 Cse 990 Cse 1120 1125 1220 1220C 3M™ Digital WallDisplay HP LaserJet 1100 1120 4050 4500 4M Plus 5000 8100 8150... - Page 51 Section Head 3M™ Digital WallDisplay (This page intentionally left blank for printed version) © 3M 2003. All Rights Reserved.
- Page 52 Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application.