3M Digital Walldisplay 9000PD Plus Operator's Manual
  1. Manuals
  2. Brands
  3. 3M Manuals
  4. Projection Screen
  5. Digital Walldisplay 9000PD Plus
  6. Operator's manual
3M Digital Walldisplay 9000PD Plus Operator's Manual

3M Digital Walldisplay 9000PD Plus Operator's Manual

Hide thumbs Also See for Digital Walldisplay 9000PD Plus:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Quick Reference Manual
3
Digital Wall Display
Operator's Guide
Guide de l'operateur
Benutzerhandbuch
Guida dell'operatore
Guía del operador
August 2005
78-6970-9428-8 Rev. A
Copyright © 2005, 3M.
All Rights Reserved.
...for projection
9000PD Plus

Advertisement

Table of Contents
loading

Related Manuals for 3M Digital Walldisplay 9000PD Plus

Summary of Contents for 3M Digital Walldisplay 9000PD Plus

  • Page 1 Digital Wall Display Operator’s Guide Guide de l’operateur Benutzerhandbuch Guida dell’operatore Guía del operador …for projection 9000PD Plus August 2005 78-6970-9428-8 Rev. A Copyright © 2005, 3M. All Rights Reserved.
  • Page 2 (This page intentionally left blank for printed version)

  • Page 3: Table Of Contents

    Fonctionnement ............................65 Télécommande .............................67 Système de menu ............................70 Entretien...............................73 Dépannage ..............................82 Service après-vente ............................84 Annexe .................................85 DEUTSCH Einleitung..............................91 Installation und Einrichtung des Systems ....................101 Bedienung ..............................106 Fernbedienung ............................108 Menüsystem ...............................111 Wartung..............................114 Fehlerbeseitigung............................123 Serviceinformationen..........................125 Anhang...............................126 © 3M 2005. All Rights Reserved.
  • Page 4 Risoluzioni dei problemi ...........................165 Informazioni per l’assistenza........................167 Appendice ..............................168 ESPAÑOL Introducción ...............................175 Instalación del sistema..........................185 Funcionamiento ............................190 Unidad de control remoto..........................192 Sistema de menús ............................195 Mantenimiento ............................198 Resolución de problemas...........................207 Información sobre reparaciones.........................209 Apéndice ..............................210 © 3M 2005. All Rights Reserved.
  • Page 5 Safety Information ............................7 Intended Use ..............................7 Product Safety Label ...........................11 Save These Instructions ..........................11 Trademarks ..............................11 Patents ................................11 3M Digital Wall Display Technical Support ....................11 FCC Statement—Class A ..........................12 EEC Statement—Class A ..........................12 Model Identification and Differences......................13 Contents ...............................14 Optional Accessories ...........................14 What’s Next? ...............................14...
  • Page 6 Troubleshooting Common Problems and Solutions .......................39 Onscreen Messages............................40 Service Information Replacement Parts ............................41 Optional Accessories ...........................41 Ordering Parts or Getting Information ......................41 Appendix Digital Wall Display Specifications....................42 ™ Input/Output Signal Specifications......................43 Computer Compatibility ..........................43 © 3M 2005. All Rights Reserved.

  • Page 7: Introduction

    Before operating this machine, please read the entire manual thoroughly. The 3M Digital Wall Display Systems are designed, built, and tested for use indoors, using 3M lamps, 3M mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.
  • Page 8 • Do not attempt to service the Wall Display other than performing routine lamp replacement. Service should only be performed by a 3M authorized service provider. Aside from the projection lamp assembly, there are no serviceable parts inside the unit.
  • Page 9 To reduce the risks associated with impact from the projection arm and tripping over the legs of the portable cart: • Do not use this Wall Display around unsupervised children. • Do not allow children to hang onto the projection arm. © 3M 2005. All Rights Reserved.

  • Page 10: Important Notes

    • Do not manually open or close the projection arm while the 3M Digital Wall Display is in operation. • Save the shipping box and packing materials in the event the 3M Digital Wall Display should ever need to be moved.

  • Page 11: Product Safety Label

    This product is covered by one or more of the following patents: U.S. Patent Number D442,205 U.S. Patent Number 6,179,426 U.S. Patent Number 6,94,609 3M Digital Wall Display Technical Support • In U.S. or Canada: 1-800-328-1371 • Web Site: http://www.3M.com/Wall Display © M 2005. All Rights Reserved.

  • Page 12: Fcc Statement-Class A

    If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation. Video Inputs The input signal amplitude must not exceed the specified level. (See Appendix for these levels.) © 3M 2005. All Rights Reserved.

  • Page 13: Model Identification And Differences

    Projection 9200IC Plus *The Copyboard feature allows you to print notes written on the 3M Digital Wall Display to an attached printer. (HP or Epson USB-compatible printer required.) **The Digital Whiteboard feature allows you to capture notes written on the 3M Digital Wall Display with an attached computer or use the 3M Digital Wall Display as an interactive display for a computer.

  • Page 14: Contents

    What’s Next? After the 3M Digital Wall Display has been installed in your meeting room, you are ready to set it up. Please read this guide thoroughly before operating your new 3M Digital Wall Display. Be sure to check our web site (www.3M.com/Wall Display) regularly for updates and supplemental information.

  • Page 15: Part Identification

    Introduction ™ Digital Wall Display Part Identification ��� � � � � ����� ����� ���� ���� ����� ����� � � � © 3M 2005. All Rights Reserved.

  • Page 16: 3M Digital Wall Display Features

    Digital Wall Display ™ 3M Digital Wall Display Features The 3M Digital Wall Display combines the following features into one sleek, sophisticated package. • Full connectivity for computer or video presentations • Large 60" diagonal screen • 4:3 screen aspect ratio matches business applications and viewing data •...

  • Page 17: Installation And System Setup

    Location of Unit • Place near AC outlet. The AC power connection is located on the lower-left corner of the 3M Digital Wall Display (the unit). The AC power cord supplied with the unit is 6 feet (2 m) long.

  • Page 18: Installing The Wall Bracket

    Note: For other types of wall material (e.g. wood, concrete, concrete block) use mounting hardware that is properly rated for the weight of the unit and is intended for specific wall material. © 3M 2005. All Rights Reserved.

  • Page 19: Hanging The 3M Digital Wall Display

    3. Remove the accessory box(es) from the top support. 4. Remove the top support. 5. Remove the plastic bag from the 3M Digital Wall Display by lifting the top of the unit and pushing the bag towards the bottom of the unit. Then set down the top.
  • Page 20 Digital Wall Display ™ Hanging on the Wall 1. If possible, position the 3M Digital Wall Display and shipping tray in front of the wall where the bracket is located. Position the unit so that the projection arm is closest to the wall.

  • Page 21: System Setup

    Digital Wall Display System Setup It only takes a few minutes to connect the 3M Digital Wall Display to your computer, VCR, DVD player, videoconference unit, or other devices. The connection panel is located underneath the bottom right corner of the 3M Digital Wall Display, under the Connection Panel Door.

  • Page 22: Operation

    1. Plug power cord into wall socket. 2. Flip on the Master Power Switch beneath the lower left corner of the 3M Digital Wall Display, near the 3M label. This should stay on at all times. Now the 3M Digital Wall Display is in standby mode. The large oval On/Off Button will be backlit amber after several seconds.

  • Page 23: Shutdown

    On/Off Button will flash red. The fan will continue to run for approximately five minutes to cool the unit. Note: If the 3M Digital Wall Display will not be moved or disconnected, leave the Master Power Switch on for your convenience.

  • Page 24: Remote Control Unit

    Remote Control Unit Features The remote control sensor is on the front lower panel of the 3M Digital Wall Display. The distance between the sensor and remote control must be shorter than 4 meters (13 feet). The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is beneath the cover.

  • Page 25: Forward Keypad

    ™ Digital Wall Display Forward Keypad Power Press to turn the 3M Digital Wall Display on/off. When power is turned on, the 3M Digital Wall Display will automatically extend the projection arm and ignite the lamp. Mute Press to temporarily turn off the sound. Press again or press the Volume + or - buttons to restore sound.

  • Page 26: Installing Or Replacing Batteries

    3. Snap the battery compartment cover back on. Note: Avoid excessive heat and humidity. Do not mix old and new batteries or different types of batteries. Note: Recycle or dispose of batteries per local and regional regulations. © 3M 2005. All Rights Reserved.

  • Page 27: Menu System

    Most adjustments and settings are available in the main menu and sub-menus. To display and navigate the menu press the 3M Digital Wall Display Menu Keypad button or the remote control Menu button. Use the Menu Keypad arrow buttons or the Direction Knob to move through the menu. Click the Trigger button to change a menu item.

  • Page 28: Picture

    Video Input Selects the display input for the Picture-In-Picture source Audio Input Selects the audio input for the Picture-In-Picture source Location Determines the location of the PIP display. Exit Menu Exit out of the menu © 3M 2005. All Rights Reserved.

  • Page 29: Configuration

    • Lamp Hours: The total time on the lamp • Optical Engine Hours: Total time on the optical engine • System Hours: Total time power has been applied to the 3M Digital Wall Display. • Software Version Number: The version of software on the Display Controller Board •...

  • Page 30: Maintenance

    Maintenance General Maintenance For general cleaning of the screen and exterior of the 3M Digital Wall Display, use a damp cloth or dry cleaning cloth such as the 3M High Performance Cleaning Cloth. Standard dry-erase cleaners may be used on the dry-erasable screens, such as Sanford...

  • Page 31: Lamp Replacement

    5. Two black wires connect to the lamp cartridge by a black plastic receptacle on the right side of the lamp cartridge. Lamp Black Receptacle Cartridge Wires © 3M 2005. All Rights Reserved.
  • Page 32 8. Holding the latch open, slide the new lamp cartridge into place. 9. Reconnect black wires to the receptacle. 10. Close the lamp housing door and tighten the screw. © 3M 2005. All Rights Reserved.
  • Page 33 Note: You must hear or feel a distinctive snap to ensure facade is securely attached. Whenever the lamp is replaced, please reset the total lamp operating time. (Refer to next page.) © 3M 2005. All Rights Reserved.

  • Page 34: Resetting Lamp Hours

    Fan Screen Cleaning The 3M Digital Wall Display has two screens located outside of the lamp cooling fans. The cooling fans are positioned above and beneath the lamp. The fan screen above the lamp should be cleaned every 1000 hours to prevent dust buildup and ensure proper operation of the 3M Digital Wall Display.

  • Page 35: Replacing Projection Screen

    Replacing the 3M Digital Wall Display screen is very simple. 1. Turn off the 3M Digital Wall Display and disconnect the power cord from the wall outlet. 2. Remove the right and left side bezels. There are two ways to remove it. Either snap it off or insert a screwdriver into the notch located on the sides of each bezel, near the top.

  • Page 36: Optical Engine Adjustment

    Carefully lift outward to remove the optical engine door. 3. Locate adjustment screw for side to side screen ������������ ������������ adjustment. Locate locking screw for side to side ������� ����� ���������� ����� adjustment. ���� © 3M 2005. All Rights Reserved.
  • Page 37 Locate locking screw for right side ���������� ���������� ������� ����� ���������� ����� adjustment. ���� 6. Loosen locking screw. Then use blade screwdriver on adjustment screw to move right side screen image up and down if required. Tighten locking screw. © 3M 2005. All Rights Reserved.
  • Page 38 Tighten locking screw. Note: After making adjustments it may be necessary to perform the side to side adjustment to center the image properly. 9. Replace the optical adjustment door. © 3M 2005. All Rights Reserved.

  • Page 39: Troubleshooting

    Connect an active input source to detected. A signal must be present for the unit. input to be selected. The input device (e.g. computer, Turn on input source DVD player, etc.) is not turned on. © 3M 2005. All Rights Reserved.

  • Page 40: Onscreen Messages

    Onscreen Messages Message Meaning No input is detected 3M Digital Wall Display is not receiving a signal from an external source. Check the cable connections and verify power is on and external source is working. Please change the lamp The lamp has 1400–1499 hours on it and needs to be changed.

  • Page 41: Service Information

    The contents of this manual are subject to change without prior notice. 3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.

  • Page 42: Appendix

    RS-232 Control Port 9-pin D-Sub Mouse Emulation Port Network RJ45 Amplifier (to speakers) 20 Watts per channel Audio System Speakers 40 Watts Max., 8 ohms Power Requirements 100~240 VAC, 50/60 Hz, 400 Watts Max. © 3M 2005. All Rights Reserved.

  • Page 43: Input/Output Signal Specifications

    72 Hz 48.1 kHz 75 Hz 46.9 kHz 85 Hz 53.7 kHz 60 Hz 48.4 kHz 70 Hz 56.5 kHz 1024x768 75 Hz 60.0 kHz 85 Hz 68.7 kHz 1280x1024 60 Hz 64.0 kHz © 3M 2005. All Rights Reserved.
  • Page 44 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.

Table of Contents