GE Profile Advantium PSB9120SFSS Dimension Manual page 2

PSB9120SF
GE Profile Series Advantium
™
Preparation WIth an Accessory Drawer
Prepare the opening
The Advantium 120V can be installed in combination with other GE/
Monogram appliances. Always follow each product's Installation
Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall to the
dimensions shown.
* For existing cutouts, a maximum
width of 28-1/2" is acceptable. If
the opening is slightly wider, secure
a furring strip on each side of the
cutout for securing the oven.
• Allow 3/4" to 2-1/8" case trim overlap
on the sides and 7/8" overlap on the
bottom of the opening for all models.
The amount of overlap on the sides
depends on the actual cutout width.
Allow 1-1/4" case trim overlap on the
top for models PSB9120 and for models
ZSC1201 and ZSC1202.
• Oven overlaps will conceal cut edges on all sides of the opening.
Note: PSB9120 series Advantium can be installed below GE/GE Profile
non-downdraft gas and electric cooktops. It CANNOT be installed below
induction or Monogram (2GU3841385) gas cooktops.
Note: PSB9120 series Advantium oven comes with two lower trim pieces.
One is for use above 36-inch height installations and one is for use below
36-inch installations. Use of the accessory drawer will replace the bottom
trim piece for applicable installations. Please see installation instructions
for full details.
120V - 30 in. Wall Oven
®
23-1/2"
30"
25-1/4"
Min.
21"
Construct
Base
Min. 3/8"
Plywood
5" min.
Supported
from floor
by 2x4 or 2x2
1" min.
Runners all
above
Four Sides
toekick
Prepare the opening (cont.)
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium and the other appliance overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.
• the support must be level and rigidly
mounted, flush with the bottom edge of
the cutout.
Installation over a GE/Monogram
Warming Drawer:
23-1/2" Construct
30"
Solid Bottom
Min. 3/8"
Plywood
Supported
25-1/4"
by 2x4 or 2x2
Min.
Runners all
Four Sides
2" Min.
21"
(3" recommended)
Per warming
drawer
requirement
5" min.
from floor
1" min.
above
toekick
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Installation over a GE/Monogram Oven
and Warming Drawer:
Warming Drawer:
Construct Solid
Bottom Min.
30" 23-1/2"
3/8" Plywood
Supported by
2x4 or 2x2
Runners all
25-1/4"
Four Sides
Min.
21" 2" Min.
(3" recommended)
Per Oven
Requirement
5" min.
from floor
2" Min.
1" min.
above Per warming drawer requirement
toekick
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
CAutION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30-
pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.
Specification Revised 7/13
240410