GE Profile Advantium PSB9120SFSS Dimension Manual

PSB9120SF
GE Profile Series Advantium
™
Suitable
bracing
21-5/8"
to support
Advantium wall oven/GE Profile over centerline
runners
of cabinet
dimensions and cabinet installation information (in inches)
(Must support 130 lbs.)
Note: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
19-1/8"
rating.
Note: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
Installation
Information:
Before installing,
consult installation
instructions packed
with product for current
dimensional data.
Note: Advantium wallovens can be installed below GE/GE Profile Series non-
downdraft gas and electric cooktops. It CANNOT be installed below induction or
Monogram (2GU3841385) gas cooktops.
Note: Advantium wall oven comes with two lower trim pieces. One is for use above
36-inch height installations and one is for use below 36-inch installations. Use of
the accessory drawer will replace the bottom trim piece for applicable installations.
Please see installation instructions for full details.
C L
2x4's or
equivalent
solid floor
120V - 30 in. Wall Oven
®
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
Series cooking tower
™
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
Cabinet width
A
B
21-1/2"
To back
of Control
29-3/4"
A
B
Conduit
(46" long)
Suitable
bracing
to support
runners
For answers to your Monogram
appliance questions, visit our website at
geappliances.com or call GE Answer Center
service, 800.626.2000.
29-3/4"
5" min.from
floor 1" min.
above toekick
Advantium Wall Oven Dimensions (in inches)and
30"
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
4-3/16"
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Junction box location
2-1/2" MIN between cutouts
recommended—2" MIN required
C L
Construct Solid Bottom
2x4's or
MIN 3/8" Plywood Supported by
equivalent
2 x 4 or 1 x 2 Runners, all Four Sides.
solid floor
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
9-1/4" cutout height
28-1/2" cutout width
2" MIN between cutouts
21-5/8"
over centerline
of cabinet 1" Min. above toekick or adjust
to oven installation height
(Must support 130 lbs.)
Cabinet width
19-1/8"
21-1/2"
To back
of Control
29-3/4"
Suitable
bracing
Conduit
to support
(46" long)
or GE
® ®
runners
®
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
25-1/8"
Cutout width
21-1/2"
Back of Control
Advantium Wall Oven Dimensions (in i
Cabinet Installation (in inches)
A
Conduit
19-1/8" (48-1/2"
long)
Note: Cabinets installed adjacent
29-3/4"
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
30"
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
4-3/16"
C L
2x4's or
equivalent
Junction box location
solid floor
A
B
2-1/2" MIN between cutouts
recommended—2" MIN required
A
B
Construct Solid Bottom
21-5/8"
MIN 3/8" Plywood Supported by
over centerline
2 x 4 or 1 x 2 Runners, all Four Sides.
of cabinet
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
(Must support 130 lbs.)
Specification Revised 7/13
9-1/4" cutout height
28-1/2" cutout width
2" MIN between cutouts
23-1/2"
Cutout depth
4-3/16"
Junction
box location
B
17-1/2"
Construct Solid
Cutout height
Bottom Min.
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
5" min.from
floor 1" min.
above toekick
21-1/2"
Back of Control
19-1/8"
29-3/4"
A= Allow 1" overlap of oven ove
Listed by
1-1/4" overlap at top edge of
Underwriters
B= Allow 11/16"-3/4" for overlap Laboratories
240410
4-3/16"
Cabinet width
25-1/8"
Cutout width
A
Conduit
(48-1/2"
long)
30"