GE Profile Advantium PSB9120DFBB Dimension Manual

C L
PSB9120DF
GE Profile Series Advantium
™
Suitable
bracing
21-5/8"
to support
Advantium wall oven/GE Profile
over centerline
runners
of cabinet
dimensions and cabinet installation information (in inches)
(Must support 130 lbs.)
Note: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
rating.
19-1/8"
Note: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
Installation
Information:
Before installing,
consult installation
instructions packed
with product for current
dimensional data.
Note: Advantium wallovens can be installed below GE/GE Profile Series non-
downdraft gas and electric cooktops. It CANNOT be installed below induction or
Monogram (2GU3841385) gas cooktops.
Note: Advantium wall oven comes with two lower trim pieces. One is for use above
36-inch height installations and one is for use below 36-inch installations. Use of
the accessory drawer will replace the bottom trim piece for applicable installations.
Please see installation instructions for full details.
2x4's or
equivalent
solid floor 29-3/4"
120V - 30 in. Wall Oven
®
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
Series cooking tower
™
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
4-3/16"
Cabinet width
A
B
21-1/2"
To back
of Control
29-3/4"
A
B
Conduit
(46" long)
Suitable
bracing
to support
runners
(Must support 130 lbs.)
19-1/8"
For answers to your Monogram
appliance questions, visit our website at
geappliances.com or call GE Answer Center
service, 800.626.2000.
5" min.from
Advantium Wall Oven Dimensions (in inches)and
floor 1" min.
Cabinet Installation (in inches)
above toekick
30"
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Back of Control
Junction box location
2-1/2" MIN between cutouts
19-1/8"
recommended—2" MIN required
C L
2x4's or
Construct Solid Bottom
equivalent
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides. solid floor
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
9-1/4" cutout height
28-1/2" cutout width
2" MIN between cutouts
21-5/8"
over centerline
of cabinet
1" Min. above toekick or adjust
to oven installation height
Cabinet width
21-1/2"
To back
of Control
29-3/4"
Suitable
bracing
Conduit
to support
or GE
® ®
(46" long)
runners
®
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
25-1/8"
Cutout width
21-1/2"
A
Advantium Wall Oven Dimensions (in i
Cabinet Installation (in inches)
Conduit
(48-1/2"
long)
29-3/4"
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
30"
A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
4-3/16"
C L
2x4's or
equivalent
Junction box location
solid floor
A
B
2-1/2" MIN between cutouts
recommended—2" MIN required
A
B
Construct Solid Bottom
21-5/8"
MIN 3/8" Plywood Supported by
over centerline
2 x 4 or 1 x 2 Runners, all Four Sides.
of cabinet
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
(Must support 130 lbs.)
Specification Revised 7/13
9-1/4" cutout height Cabinet width
28-1/2" cutout width
2" MIN between cutouts
23-1/2"
Cutout depth
4-3/16"
Junction
box location
B
17-1/2"
Construct Solid
Cutout height
Bottom Min.
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
5" min.from
floor 1" min.
above toekick
Cutout width
21-1/2"
Back of Control
Conduit
19-1/8" (48-1/2"
long)
29-3/4"
Listed by
A= Allow 1" overlap of oven ove
Underwriters
1-1/4" overlap at top edge of c
Laboratories
B= Allow 11/16"-3/4" for overlap
240407
4-3/16"
25-1/8"
A
30"