Fujitsu M3092DC Operation Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Scanner
  5. M3092DC
  6. Operation manual
Fujitsu M3092DC Operation Manual

Fujitsu M3092DC Operation Manual

Image scanner
Hide thumbs Also See for M3092DC:
Table of Contents

Advertisement

Quick Links

Download this manual
C150-E131-02EN
M3092DC Image Scanner
OPERATION GUIDE
Top
2-

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu M3092DC

Summary of Contents for Fujitsu M3092DC

  • Page 1 C150-E131-02EN M3092DC Image Scanner OPERATION GUIDE...
  • Page 2 Treatment of This Manual Since this manual contains important information for using the M3092DC, read it thoroughly before using the product. Use the M3092DC only after thoroughly reading and understanding especially the section "Important Alert Messages" in this manual. Keep this manual handy, and store it carefully.
  • Page 3 Notice to Hiermit wird bescheinigt, daß der/dieldas German Users M3092DC in Übereinsstimmung mit den Bestimmungen der AmtsblVfg 243/1991 funkentstört ist. Der Deutschen Bundespost wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung der Serie auf Einhaltung der Bestimmungen eingeräumt.
  • Page 4 Trademark Acknowledgment Fujitsu is a registered trademark of Fujitsu Limited. Second Edition, October 1999 The contents of this manual may be revised without prior notice. The contents of this manual shall not be disclosed in any way or reproduced in any media without the express written permission of Fujitsu Limited.
  • Page 5 Preface Thank you very much for your purchase of the M3092DC Image Scanner. The M3092DC Image Scanner can read very fine color images. As this manual explains the basic handling of the scanner, read it carefully to use the scanner properly.
  • Page 6 Every user is requested to use this product including the manuals and software supplied with the product at the user's own responsibility. Fujitsu assumes no liability with respect to any damage or loss caused to data as the result of using this product.
  • Page 7 An alert message consists of an alert signal and alert statements. The alert signals and their meanings are as follows. M3092DC Image Scanner Operation Guide This indicates a hazardous situation that could result in serious personal injury if the user does not perform the procedure correctly.
  • Page 8 The symbol marked with indicates what must be observed. The concrete meaning of the action is illustrated in the symbol. (The example at left directs the operator to disconnect the power plug from the outlet.) M3092DC Image Scanner Operation Guide...
  • Page 9 Important Alert Items Important Alert Messages Important alert messages applicable to the M3092DC Image Scanner are listed below. Observe these directions for safe operation of the scanner. Alert concerning power supply Do not insert the AC adapter to any outlet other than one dedicated to Prohibited 15 A at 100 VAC.
  • Page 10 Failure to do so could result in a fire. In case of thunder, disconnect the AC adapter from the outlet. Failure to do so could result in damage to the scanner or other property of the customer. M3092DC Image Scanner Operation Guide...
  • Page 11 The AC adapter is free of abnormal heat, corrosion, or bending. The AC adapter and outlet are free of dust. The power cord is free of breakage or scratches. If an abnormality is found, call your sales agency or Fujitsu Limited. M3092DC Image Scanner Operation Guide...
  • Page 12 A fire could result. Do not use the scanner in the bathroom or where it is easily Water moistened. A fire or electric shock could result. viii M3092DC Image Scanner Operation Guide...
  • Page 13 Disconnect the AC adapter from the outlet before moving the scanner. Plug Failure to do so could damage the power cord resulting in a fire or electric shock, or cause the scanner to fall and cause injury. M3092DC Image Scanner Operation Guide...
  • Page 14 Plug scanner interior, promptly disconnect the AC adapter from the outlet, then call your sales agency or Fujitsu Limited. Failure to do so could result in a fire or electric shock. If the scanner has been dropped or the cover has been damaged, disconnect the AC adapter from the outlet, then call your sales agency or Fujitsu Limited.
  • Page 15 When removing a jammed document or performing fault recovery, be careful not to touch sharp edges. This could result in personal injury. Do not touch the document entry or exit port while the scanner is operating. This could result in personal injury. M3092DC Image Scanner Operation Guide...
  • Page 16 When disposing of the scanner, separate it from general waste. The fluorescent lamp contains mercury. Do not put it in waste to be processed at a general waste-dumping site. For disposal of fluorescent lamps, follow the regulations or rules of the relevant local government. M3092DC Image Scanner Operation Guide...

  • Page 17: Table Of Contents

    Setting the SCSI ID... 2-7 2.3.5 Installing Driver and Software... 2-8 Setting Up the Document Support... 2-9 CHAPTER 3 Operation... 3-1 Notes concerning Operation ... 3-1 Reading a Document on the Flat Bed... 3-3 M3092DC Image Scanner Operation Guide Contents xiii...
  • Page 18 ...4-8 4.4.2 Procedure for Replacing the Pad ...4-9 4.4.3 Procedure for Replacing the Pick Roller ...4-10 CHAPTER 5 When you suspect a Fault Occurred ... 5-1 APPENDIX Installation Specifications ... A-1 M3092DC Image Scanner Operation Guide...

  • Page 19: Chapter 1 Notes Concerning Use

    This section provides an outline of the M3092DC Image Scanner and explains its characteristics. 1.1.1 M3092DC Image Scanner The M3092DC Image Scanner can read very fine color images. It can also work with attached software as follows: Scan software enables the saving of data scanned with the scanner in TIFF format in a personal computer.

  • Page 20: Confirming The Content Of Packing Box

    1.2 Confirming the Content of Packing Box The M3092DC Image Scanner is packed together with accessories in a packing box. Take out the scanner and accessories from the packing box and confirm missing items with the attached packing list.

  • Page 21: Component Names And Functions

    1.3 Component Names and Functions This section shows the components of the scanner and explains their functions. Front Document support Document guide Automatic document feeder M3092DC Image Scanner Operation Guide Copy density dial Density dial Down Function No. display panel Function Function button...
  • Page 22 Switches between read modes. You can confirm the current read mode with the Function No. display panel. Starts the operation specified by the Function button. Scans the document placed in position. Stays lit while power is being supplied. M3092DC Image Scanner Operation Guide...
  • Page 23 Cover open lever AC adapter connector Interface connector SCSI terminator switch SCSI ID switch M3092DC Image Scanner Operation Guide Function Opens and closes the automatic document feeder. Accommodates the AC adapter. Accommodates an interface cable to be connected to a personal computer.
  • Page 24 Internal Ejection roller Plastic roller Feed roller Eject roller Component Name Function Feed roller, eject roller, Sends documents. plastic roller M3092DC Image Scanner Operation Guide...

  • Page 25: Chapter 2 Installation And Connection

    2.1 Notes concerning Ins tallation When installing the image scanner, adhere to the following installation location and environment notes: M3092DC Image Scanner Operation Guide Fire or electric shock -- Do not alter or disassemble the scanner. High voltage components are inside.
  • Page 26 Avoid static electricity, which could result in a scanner malfunction. For the floor and workbench on which/near which the scanner will be placed, select materials that do not easily generate static electricity. M3092DC Image Scanner Operation Guide...

  • Page 27: Mounting The Document Support

    When documents are actually read, the user can raise the document support slide plate according to the size of the documents. For information regarding the setup of the document support, see Section 2.4, “Setting up the Document Support.” M3092DC Image Scanner Operation Guide...

  • Page 28: Connection

    Do not alter the power cable in any way. Do not use a power cable if it is damaged or the plug does not fit snugly into the outlet. M3092DC Image Scanner Operation Guide...

  • Page 29: Connecting The Scsi Cable

    If the image scanner is the end termination of the SCSI bus, set the SCSI terminator switch to ON (default setting). M3092DC Image Scanner Operation Guide Fire, electric shock, or fault Insert the power cable all the way to the rear of the outlet.

  • Page 30: Connecting The Power Cable

    While the driver and the software is active, the reading lamp turns on or off in accordance with the status of the connected personal computer. Inlet M3092DC Image Scanner Operation Guide...

  • Page 31: Setting The Scsi Id

    The factory default value (SCSI ID = 5) is used for these numbers. 3) After setting the address number corresponding to the target SCSI ID, connect the power cable to the outlet. M3092DC Image Scanner Operation Guide SCSI ID switch Meaning...

  • Page 32: Installing Driver And Software

    To install the driver, run “Setup.exe” in the \Driver\Disk1 folder on the CD-ROM. The Fujitsu TWAIN32 driver is installed and registered on the TWAIN32 source selection screen. To install other software, run “Setup.exe” in the \Tools\Disk1 folder on the CD-ROM.

  • Page 33: Setting Up The Document Support

    2.4 Setting Up the Document Support Raise the slide of the document support according to the size of documents as follows: 1) When using an A4-size document, raise the slide of the document support as shown below. M3092DC Image Scanner Operation Guide Paper extension Slide...

  • Page 35: Chapter 3 Operation

    3.1 Notes concerning Operation When operating the equipment, adhere to the following points: M3092DC Image Scanner Operation Guide Fire or electrical shock If heat, smoke, offensive odor, or noise is emitted from the equipment, turn off the power switch of the main unit and disconnect the power plug from the outlet.
  • Page 36 If lightening occurs nearby, disconnect the power plug from the outlet; otherwise, the equipment may be damaged. Fault Do not push auto-fed paper too strongly or place a heavy object on it. Doing so may cause the equipment to malfunction. M3092DC Image Scanner Operation Guide...

  • Page 37: Reading A Document On The Flat Bed

    When a document is smaller than the document bed, follow the procedure below. Reference mark M3092DC Image Scanner Operation Guide While the equipment is reading the document, do not open the document cover and look into the light of the fluorescent lamp.
  • Page 38 6) Select a reading mode on the driver screen, and read the document. Do not hold or open the document cover during reading. 7) When finishing reading, open the document cover and remove the document. Portrait Shorter side M3092DC Image Scanner Operation Guide Document bed Document...

  • Page 39: Reading A Thick Document

    Paper type - High-quality paper - PP paper (paper specified by Xerox Corporation) Ream weight 45 to 90 kg/ream (52.3 to 104.7 g/m Size A4, A5, B5, letter size, legal size, and name card size (A8) M3092DC Image Scanner Operation Guide...
  • Page 40 Cloth, metal sheet, and OHP sheet made of other materials than paper Photographic paper Paper perforated peripherally Nonrectangular paper Paper lighter than 45 kg /real (52.3 g/m (104.7 g/m Paper of uneven width M3092DC Image Scanner Operation Guide ) or heavier than 90 kg/ream...

  • Page 41: Setting Documents

    Level both ends of the documents so that they can be read correctly. Set the documents as follows: For single-side reading: Place the reading side facing the document support surface. M3092DC Image Scanner Operation Guide and similarly loosen it. 4 m m 4 mm...
  • Page 42 For double-sided reading: Place the surface (first page) facing the document support surface. Set the documents. Base side M3092DC Image Scanner Operation Guide...

  • Page 43: Scanning Documents

    Excessively strong insertion results in feeding multiple pages simultaneously. Also, make sure that the ends of the pages are not folded down. M3092DC Image Scanner Operation Guide ) paper) for A4 or legal size or smaller. For single-side reading: Place the reading side facing down (document support surface).
  • Page 44 If the application software does not start and the Function No. display panel displays the copy count again, the scan processing is canceled. 8) After finishing reading, remove the documents from the stacker. 3-10 M3092DC Image Scanner Operation Guide...
  • Page 45 ! Note When validating the Duplex button and Scan button on the equipment using the TWAIN driver, you must validate "Follow Instructions on the Operator Panel of the Equipment" on the Fujitsu M3092DC TWAIN32 operation environment setting screen. ! Key point You can perform a simple editing operation of the data of a scanned document by using Image.

  • Page 46: Copying Documents

    3-12 ) paper) for A4 or legal size or smaller. For single-side reading: Place the reading side facing down (document support surface). For double-sided reading: Place the surface (first page) facing down (document support surface). M3092DC Image Scanner Operation Guide...
  • Page 47 If the application software does not start and the Function No. display panel displays the copy count again, copy processing is canceled. 10) After finishing reading, remove the documents from the stacker. M3092DC Image Scanner Operation Guide 3-13...
  • Page 48 Copy screen and click "Copy". This specification becomes valid for subsequent copy operations. To cancel this option, uncheck "Enlarge/Reduce to fit Print Area". M3092DC Image Scanner Operation Guide Copy density dial Function No. display panel Function button Duplex button...

  • Page 49: Chapter 4 Daily Maintenance

    1) Remove the document from the document support. 2) Open the automatic document feeder by pulling it toward you while raising the cover open lever. Automatic document feeder M3092DC Image Scanner Operation Guide Cover opening lever. Cover open lever...
  • Page 50 Push the center. After restoring the automatic document feeder into position, make sure that it is closed completely. If the automatic document feeder is not properly closed , a paper jam or reading error may occur. M3092DC Image Scanner Operation Guide...

  • Page 51: Daily Maintenance

    Keep the following point in mind: If the equipment surface, document support, or automatic document feeder is soiled, clean it according to Section 4.3, "Cleaning." Especially, be sure to clean the automatic document feeder. M3092DC Image Scanner Operation Guide...

  • Page 52: Cleaning

    Never use an organic solvent such as thinner. Do not allow moisture to get inside the device during cleaning. Fire or electrical shock When cleaning the equipment, turn off the power by disconnecting the AC adapter power plug from the outlet. M3092DC Image Scanner Operation Guide...

  • Page 53: Cleaning The Automatic Document Feeder

    1) Open the automatic document feeder by pulling it toward you while raising the cover open lever. 2) Clean the following components with a dry cloth or a cloth moistened with isopropyl alcohol: Pad: M3092DC Image Scanner Operation Guide Cloth Document cover Document presser Document holding pad Document bed Clean this component downward (in arrow direction).
  • Page 54 If black foreign matter attaches to the component, the document feed performance is affected; therefore, thoroughly clean it. Paper guide surface (white part): Clean this component gently. Flat bed glass surface: Clean this component gently. M3092DC Image Scanner Operation Guide...
  • Page 55 Picking arm Pick arm Pick spring Picking spring Feed roller 3) Restore the automatic document feeder into position. M3092DC Image Scanner Operation Guide Plastic roller Picking roller Pick roller Ejection roller Eject roller Automatic document feed glass surface (this component is also present on the automatic document feeder.)

  • Page 56: Consumables And Regular Replacement Components

    Fire or electrical shock When replacing any of the equipment's consumables, first disconnect the AC adapter power plug from the outlet. Parts No. Replacement cycle (standard) PA03209-F010 Every 12,000 sheets or annually PA03209-F012 Every 50,000 sheets or annually M3092DC Image Scanner Operation Guide...

  • Page 57: Procedure For Replacing The Pad

    3) Remove the pad. Step 1: Step 2: Step 1 M3092DC Image Scanner Operation Guide Push the pick arm in the automatic document feeder in the arrow direction. Pull out the pad by using such as a ballpoint pen at both ends (a and b) of the pad.

  • Page 58: Procedure For Replacing The Pick Roller

    (in the arrow direction). 4-10 Check that the pad is mounted completely. If the pick roller is not mounted correctly, a document feeding error such as a paper jam may occur. M3092DC Image Scanner Operation Guide...
  • Page 59 Push the paw and the center of the pick roller with your hands to completely insert the roller. M3092DC Image Scanner Operation Guide Knob Check that the pick roller is mounted completely.

  • Page 61: Chapter 5 When You Suspect A Fault Occurred

    Is the interface cable connected correctly? Is the SCSI terminating resistor switch set correctly? M3092DC Image Scanner Operation Guide Correction Connect the AC adapter correctly. Turn off the power once by disconnecting the AC adapter. Then, turn on the power again by connecting the power cable.
  • Page 62 Document Feeder." Replace the pad. Clean the pick roller according to Section 4.3, "Cleaning the Automatic Document Feeder." Replace the pick roller. Remove foreign matter from the transfer path (see Section 4.1, "Handling a Paper Jam"). M3092DC Image Scanner Operation Guide...

  • Page 63: Appendix

    Operating consumption Not operating Permissible range Equipment of temperature and status humidity Temperature Humidity (%) M3092DC Image Scanner Operation Guide Specification Width Depth 100 V to 240 V Single 50/60 Hz 39 W or less 8 W or less Operating...
  • Page 64 Document holding pad, or the ADF clean? Does the document set in straight in the document support? M3092DC Image Scanner Operation Guide Correction When the device is used in a low temperature environment, it may happen that the FB lamp is difficult to turn on.
  • Page 65 Document does not feed. (Document feed stops half way.) *Double feed: paper scanned in lying on top of another. M3092DC Image Scanner Operation Guide Item to be Checked Is the Pad clean? Has the Pad worn out? Is the pick roller clean?
  • Page 66 External dimensions (598) M3092DC Image Scanner Operation Guide...

Table of Contents