Pioneer ND-BT1 Owner's Manual

BLUETOOTH UNIT
APPAREIL BLUETOOTH
Owner's Manual
Mode d'emploi
ND-BT1
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL: 1-877-283-5901
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd. Manuel Avila Camacho 138 10 piso
Col. Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
Published by Pioneer Corporation.
Copyright © 2006 by Pioneer Corporation.
All rights reserved.
Publication de Pioneer Corporation.
Copyright © 2006 Pioneer Corporation.
Tous droits de reproduction et de traduction
réservés.
Printed in Japan
Imprimé au Japon
< KOKHF > < 06B00000 > <CRD4118-A> E
English
Information to User
This transmitter must not be co-located or
operated in conjunction with any other
This equipment has been tested and found to
antenna or transmitter.
comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules.
This equipment complies with FCC/IC radiation
These limits are designed to provide reason-
exposure limits set forth for uncontrolled
able protection against harmful interference in
equipment and meets the FCC/IC radio fre-
a residential installation.
quency (RF) Exposure Guidelines in
This equipment generates, uses and can radi-
Supplement C to OET65 and RSS-102 of the IC
ate radio frequency energy and, if not installed
radio frequency (RF) exposure rules. This
and used in accordance with the instructions,
equipment has very low levels of RF energy
may cause harmful interference to radio com-
that it is deemed to comply without testing of
munications. However, there is no guarantee
specific absorption ratio (SAR).
that interference will not occur in a particular
installation.
WARNING
If this equipment dose cause harmful interfer-
ence to radio or television reception, which can Handling the cord on this product or cords asso-
be determined by turning the equipment off ciated with accessories sold with the product
and on, the user is encouraged to try to correct may expose you to chemicals listed on proposi-
the interference by one or more of the follow- tion 65 known to the State of California and other
ing measures: governmental entities to cause cancer and birth
defects or other reproductive harm. Wash hands
— Reorient or relocate the receiving antenna.
— Increase the separation between the equip- after handling.
ment and receiver.
If you want to dispose this prod-
— Connect the equipment into an outlet on a
uct, do not mix it with general
circuit different from that to which the
household waste. There is a sepa-
receiver is connected.
rate collection system for used
— Consult the dealer or an experienced
electronic products in accordance
radio/TV technician for help.
with legislation that requires
proper treatment, recovery and
Alteration or modifications carried out without
recycling.
appropriate authorization may invalidate the
user's right to operate the equipment.
Private households in the 25 member states of
the EU, in Switzerland and Norway may return
FCC ID : AJDK011
their used electronic products free of charge to
MODEL NO. : ND-BT1
IC : 775E-K011 designated collection facilities or to a retailer (if
you purchase a similar new one).
This device complies with Part 15 of FCC Rules
For countries not mentioned above, please con-
and RSS-Gen of IC Rules. Operation is subject
tact your local authorities for the correct method
to the following two conditions: (1) this device
of disposal.
may not cause interference, and (2) this device
must accept any interference, including inter- By doing so you will ensure that your disposed
ference that may cause undesired operation of product undergoes the necessary treatment,
this device. recovery and recycling and thus prevent potential
MADE IN JAPAN negative effects on the environment and human
health.
This class B digital apparatus complies with
Canadian ICES-003.
About this unit Installation notes
This unit is used to connect a Bluetooth enabled cellular
Velcro tape (hard) × 2
phone to a Pioneer HDD Navigation System.
2 m (6 ft. 7 in.)
About Bluetooth
backside
Bluetooth is a short-range wireless radio connectivity Velcro tape (soft) × 2
technology that is developed as a cable replacement for
cellular phones, handheld PCs and other devices.
Bluetooth operates in 2.4 GHz frequency range and
• This unit may be installed in relatively unnoticeable
transmits voice and data at speeds up to 1 megabit per
positions such as the passenger seat floor, however,
second. Bluetooth was launched by a special interest
before fixing the unit, check the reception condition
group (SIG) that comprises of Ericsson Inc., Intel Corp.,
of the Bluetooth unit with the setup-status monitor of
Nokia Corp., Toshiba and IBM in 1998, and it is currently
navigation system.
developed by nearly 2 000 companies worldwide.
• Referring to Operation Manual included in navigation
system, check the connection and fine-tune the
• The Bluetooth word mark and logos are owned by the
reception of this unit.
Bluetooth SIG, Inc. and any use of such marks by
• Thoroughly wipe off the surface before affixing the
Pioneer Corporation is under license. Other trade-
velcro tape.
marks and trade names are those of their respective
• Do not install the unit where it may (i) obstruct the
owners.
driver's vision, (ii) impair the performance of any of
the vehicle's operating systems or safety features,
Operating environment
including air bags, hazard lamp buttons or (iii) impair
the driver's ability to safely operate the vehicle.
This unit should be used within the temperature ranges
• When disconnecting a connector, pull the connector
shown below.
itself. Do not pull the lead, as you may pull it out of the
Operating temperature range : -10 to +60 °C
connector.
(14 to 140 °F)
• Do not install the unit in places where it may become
EN300328 ETC test temperature : -20 and +55 °C
subject to high temperatures or humidity, such as:
(-4 and 131 °F)
* Places close to a heater outlet.
* Places exposed to direct sunlight, such as on top of
• The line-of-sight distance between this unit and your
the dashboard or the rear shelf.
cellular phone must be 10 meters or less in sending
and receiving voice and data via Bluetooth technol- • Places that may be splashed by rain, for example
ogy. However, the transmission distance may become close to the door.
• Use supplied velcro tapes to secure the unit so that it
shorter than the estimated distance, depending on
doesn't move. It is extremely dangerous if cords are
the environment in use.
exposed on the floor as they may become entangled
• There are some Bluetooth enabled cellular phones
that can be incompatible with this unit due to their with the brake pedal etc. Hide cords so that they do
Bluetooth version. not get in the way when you are driving.
• Do not disassemble or modify this unit. To do so may
• The performance test of this unit with all Bluetooth
cause a fault.
enabled cellular phones is not conducted. Also, it is
not guaranteed that this unit can be connected to all
Bluetooth enabled cellular phones.
Specifications
• About the Bluetooth profile and its overview
General
It is required that the Bluetooth enabled cellular
Max. Current Consumption ......0.25 A
phone to be connected to this unit is implemented
with the same profile. Dimensions (W x H x D) ............89 mm x 16 mm x 48 mm
HFP (Hands Free Profile): the profile used for hands- (3-1/2 x 5/8 x 1-7/8 in.)
free calling
Weight........................................0.16 kg (0.33 lbs)
OPP (Object Push Profile): the profile used for trans-
ferring data such as address books
Bluetooth
Version ......................................Bluetooth 1.1 certined
Maximum Output Power ..........+4 dBm (Power Class 2)