Table of Contents
Advertisement
Parts and Functions
Indoor Unit
1
2
3
5
Inlet
1
1
Inlet grille
2
2
3
3
Air Purifying Filter (inside)
Outlet
4
5
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
Display board
7
1
2
1
Signal receiver hole
2
ON/OFF
display
3
Ambient temp.display
When receiving the remote
control signal, display the set
temperature and in the rest
time the room temperature is
displayed and this room
temperature is only for reference.
Outdoor Unit
OUTLET
1 4
INLET
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press
or
increase or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
Horizontal flap
4
5
(adjust up and down air flow
Don't adjust it manually)
Vertical blade
6
6
(adjust left and right air flow)
4
3
5
TIMER ON\OFF display
4
TIMER ON-OFF display
SLEEP display
Note to the power failure resume:
press the sleep button ten times in five seconds and
enter function after hearing four sounds.And press
the sleep button ten times within five seconds and
leave this function after hearing two sounds.
5
COOL\HEAT\Dry\ AUTO
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
to set correct time. Each press will
HSU-18 24HEK13/R2
Remote controller
16
14
13
12
4
5
11
6
8
7
2
1.CODE
Used to select CODE A or B
which
will be displayed on
LCD.
Please select A without
special
explanation.
2.LIGHT button
Control the lightening and
extinguishing of
LED display board.
3. TIMER button
4. CLOCK button
5. SLEEP button
NOTE:
display
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.
Loading of the battery
4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation,
please
remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
24
System Configuration
7. HOUR button
8. MODE button
9. ON/OFF button
17
10. TIMER ON display
11. FAN SPEED display
18
19
LOW
12. LOCK display
20
13. SWING display
21
14. SLEEP display
22
16. Operation mode display
23
Operation mode
24
Remote controller
25
17.Signal sending display
26
18. POWER/SOFT display
19.
TEMP display
28
20.
TIMER OFF display
CLOCK display
21.
29
22.
TEMP button
30
23.
FAN SPEED button
24.
SWING button
25. .
HEALTH AIRFLOW button
26. POWER/SOFT button
28. SET button
29. LOCK
If pressed, the other buttons
be disabled.Press it once
will
again,lock will be cancelled.
30. RESET
the indoor
When the remote controller
appears abnormal,use a
sharp pointed article to press
this button to reset the remote
controller normal.
1
Remove the battery cover;
2
2
Load the batteries as
illustrated. 2 R-03 batteries,
1
resetting key(cylinder);
3
Be sure that the loading
3
is in line with the " + "/"-";
reload several minutes later.
Domestic Air Conditioner
MED
HI
AUTO
AUTO
COOL
DRY
FAN
HEAT
button
button
Advertisement
Table of Contents
