Download  Print this page
   

Advertisement

CD-BA250H/CD-BA2600H
CP-BA250H/CP-BA2600H
Speaker system
1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Wire

Setting the Clock

In this example, the clock is set for the 24-hour (0:00) display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK button and within 5 seconds, press the MEMO-
RY/SET button.
3
Press the TUNING/TIME (
hour display and then press the MEMORY/SET button.
"0:00"
The 24-hour display will appear.
(0:00 - 23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00"
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
(Refer to step 3 under "If trouble occurs")
OPERATION MANUAL
or
) button to select 24-hour or 12-
3
4
Press the TUNING/TIME ( or ) button to adjust the hour and then
press the MEMORY/SET button.
Press the TUNING/TIME (
Holdit down to advance continuously.
When the 12-hour display is selected, "AM" will change automatically to "PM".
5
Press the TUNING/TIME ( or
then press the MEMORY/SET button.
Press the TUNING/TIME (
minute. Hold it down to change the time in 5-minute intervals.
The hour will not advance even if minutes advance from "59" to "00".
The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
To confirm the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the Clock" from the beginning. If the time display is flashing, step 3
(for selecting the 24-hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents. [Perform to step 3 under "If trouble occurs"
2 Perform "Setting the Clock" from the beginning.
– 6 –
1
2
3
or
) button once to advance the time by 1 hour.
) button to adjust the minutes and
or
) button once to advance the time by 1
4

Advertisement

   Related Manuals for Sharp CD-BA250H

   Summary of Contents for Sharp CD-BA250H

  • Page 1: Setting The Clock

    CD-BA250H/CD-BA2600H CP-BA250H/CP-BA2600H Speaker system 1. Tweeter 2. Woofer 3. Bass Reflex Duct 4. Speaker Wire OPERATION MANUAL Setting the Clock Press the TUNING/TIME ( or ) button to adjust the hour and then press the MEMORY/SET button. Press the TUNING/TIME ( ) button once to advance the time by 1 hour.
  • Page 2: Troubleshooting Chart

    Many potential "problems" can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your author- Symptom Possible cause ised SHARP dealer or service centre. Cannot record. Is the erase-prevention tab removed? General Cannot record tracks with proper Is it a normal tape? (You cannot record on sound quality.
  • Page 3 CD-BA250H/CD-BA2600H – 8 –...
  • Page 4 CD-BA250H/CD-BA2600H – 9 –...
  • Page 5 CD-BA250H/CD-BA2600H Using the Radio Data System (RDS) Information provided by RDS RDS is a broadcasting service which a growing number of FM stations provide. These FM stations send additional signals along with their regular programme Each time the DISPLAY MODE button is pressed, the display will switch as fol- signals.

This manual also for:

Cd-ba2600h

Comments to this Manuals

Symbols: 0
Latest comments: