BASIC OPERATION
HOW TO SET A DELAYED RECORDING
8.
Enter the start time using the [
NUMBER BUTTONS
(when entering less than 10 minutes add a '0'
before the number), for example for 21:05 start,
2 1 0 5
press
. Then press
9.
Enter the stop time, for example for 22:30 stop,
press
2 2 3 0
.
10.
If you wish to change the
SPEED
, use the [
[
/
] to select standard play (SP), long
play (LP) or extended play (EP) as required.
11.
[See
NOTE
below]. For VPS/PDC setting use
[
/
]
the
to highlight the final column. Using
the [
/
] will select VPS/PDC ON or OFF
( * = ON - = OFF).
12.
Press
SET
to confirm.
•
The MENU now shows all the timer settings you
have entered. If you wish to make additional
timer recordings, repeat this procedure.
13.
When you have completed entering timer
settings, press
MENU
from the TV screen.
14.
Ensure that the tape on which you wish to
record is inserted into the VCR, then press
TIMER ON/OFF
TIMER POWERSAVE/TIMER STANDBY mode.
will be shown on the display.
NOTES:
•
It is essential that the start time as it appears in the TV listing is used to program the VCR,
as this information is used to identify the VPS/PDC signal corresponding to your
programme.
•
VPS/PDC is a signal broadcast by some TV stations which adjusts the start and stop time
of your VCR recording. This ensures that if there is a change in broadcast time for your
programme the VCR will still record the whole programme.
•
If
flashes a video tape has not been inserted into the VCR.
•
If the video tape is ejected when the VCR tries to record the record protection tab has
been removed.
•
During recording, press
recordings to be made, the VCR will return to TIMER POWERSAVE/TIMER STANDBY.
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
/
] or the
hours first then minutes
SET
to confirm.
RECORDING
/
] to highlight SP. Press
to remove the menu
once to place the VCR in
STOP
(
) to cancel the recording. If there are further
or www.sharp.co.uk/support
DA T E
P R S T AR T S T OP
2 1 / 0 6
0 2
9 / 0 7 D 0 3
- - / - -
- -
- - / - -
- -
DA T E
P R S T AR T S T OP
2 1 / 0 6
0 2
9 / 0 7 D 0 3
- - / - -
- -
- - / - -
- -
DA T E
P R S T AR T S T OP
2 1 / 0 6
0 2
9 / 0 7 D 0 3
- - / - -
- -
- - / - -
- -
18
1 / 2
1 2 : 0 0
1 3 : 0 0 S P *
2 1 : 0 5
- : - -
S P *
- : - -
- : - -
- - -
- : - -
- : - -
- - -
1 / 2
1 2 : 0 0
1 3 : 0 0 S P *
2 1 : 0 5
2 2 : 3 0
L P
- : - -
- : - -
- - -
- : - -
- : - -
- - -
1 / 2
1 2 : 0 0
1 3 : 0 0 S P *
2 1 : 0 5
2 2 : 3 0 L P
- : - -
- : - -
- - -
- : - -
- : - -
- - -
*
-
Need help?
Do you have a question about the VC-S2000HM and is the answer not in the manual?