Related Manuals for JARLTECH JB-1300
Summary of Contents for JARLTECH JB-1300
- Page 1 ISO 9002 Certified Lead with technology Win customers with service JB-1300 Serial Model iButton Key Reader OPERATION MANUAL...
- Page 2 Dallas and its related copartner. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Jarltech. Every effort has been made to ensure that the information in this manual is accurate.
- Page 3 This equipment has been tested and found to comply with the limits for Class A digital device. Pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and if not installed and used in accordance with the instructions may cause harmful interference will not occur in a particular installation.
- Page 4 Contents Chapter 1. Introduction__________________________Page 5-5 ____________________ Chapter 2. Specification___ Page 6-7 _________________________ Chapter 3. Utility__ _Page 8-13 Appendix I: Packing List_________________________ Page 14...
-
Page 5: Chapter 1. Introduction
Jarltech JB-1300 ibutton key reader is a smart device specially designed to be used with Dallas ibutton keys. Customer may use JB-1300 to read ID and data from a ibutton key by touching action. Once the key touchs the gutter of reader, then key data will through keyboard or RS232 mode outputing to receiver such as Personal Computer...etc. -
Page 6: Chapter 2. Specification
Specification • • • • • • • i Button Reader • One phone jack I/O Ports • One gutter for key set. • A green LED will turn on when powered on; red to indicate Indicator the operation status and error status for trouble shooting •... - Page 7 Cables Picture 2-1 RS232 output Picture 2-2 Keyboard output...
-
Page 8: Chapter 3. Utility
NOTE: JB-1300 can only program with RS232 communication. Setp2 Power ON The green LED on the reader will turn on. Then, touch key to the reader with JB-1300 utility, the orange LED will be turned on while data reading. Setp3 Install JB-1300 utility to your HDD Run "setup.exe"... - Page 9 Setp4 Detecting JB-1300 Utility will detect COM port for search device(JB-1300). User may start to define related setting, and test reader after system detected JB-1300 of each COM port.and related paramters. Setp5 Related setting with Page1 (See picture 3-1) picture 3-1...
- Page 10 In this item, 1. Press"Open" to execute a file that user already saved. 2. Press "Save" to save existing configuration. 3. Press "Auto detect device when utility startup" to search COM port and connected device. 4. Press "Exit" to close this utility. NOTE: The "...
- Page 11 [On remove][Delimit]. User may set them with following items. Select "baud Rate Value" from 300 to 115200bps. It can be choose from 300 bps to 115200 bps to set JB-1300 baud rate.( Default is 9600 bps) Select "Delimiter" with <CR>+<LF> / <TAB> / <LF> / <CR>...
- Page 12 The setting only uses with Keyboard mode. 9. Press [Save setting to JB-1300] to save setting, there are two ways to help you to save setting, one is via RS232 mode, another is Keyboard wedge.( As picture 3-4 )
- Page 13 Setp7 Related setting (See picture 3-5) With RS232 output mode test: Connect RJ-45 male cable to button reader, connect the other end with DB9 male cable to COM port. 1. Select "Data read test" on the page 2 2. After touch the key, key's data will shown in the bottom window 3.
-
Page 14: Appendix I: Packing List
• • • • • • • Packing List • Main Unit (Button Reader) 1 SET • Keyboard Interface Y-Cable 1 PCS • RS232 Interface Cable 1 PCS • RCADC cable 1 PCS • CD title with one manual and one JB-1300 Utility 1 PCS... - Page 15 Version 3.0...