Samsung SCH-811 Service Manual page 28

Command No. Signal. Name
(OP,AB,RB)
40(A8,4,0) T_VOC_CDMA_UNITY _GAIN_I
41(A9,0,0) T_VOC_FM_HFRX_UPGAIN_I
42(AA,1,0) T_DTMFON_I
43(AB,0,0) T_DTMFOFF_I
44(B0,0,0) T_COMPANDORON_I
45(B1,0,0) T_COMPANDOROF_I
46(B2,0,0) T_FM_VCLINE_I*
47(B3,0,0) T_FM_AUD_GAIN_I
48(B4,0,0) T_VIBRATOR_ON_I
49(B5,0,0) T_VIBRATOR_OFF_I
50(B6,0,4) T_BATT_TYPE_I
51(B7,1,1) T_BBA_I
52(B9,2,2) T_HW_VERSION_I
53(BA,3,0) T_CARRIER_I
54(BB,1,0) T_VOC13K_I
55(AC,1,0) T_EXT_AUDIO_I
56(AD,0,0) T_LOOP_BACK_I
57(BC,0,0) T_MIC_ON_I
58(BD,0,0) T_MIC_OFF_I
59(BE,0,0) T_ALLPATH_I
60(BF,3,0) T_FM_TX_GAIN_I
61(C0,3,0) T_FM_RX_GAIN_I
62(C1,3,0) T_DTMF_VOL_TX_I
63(C2,3,0) T_TX_LIMITER_I
64(C3,3,0) T_FM_SAT_LEVEL_I
65(C4,3,0) T_FM_FREQ_SGAIN_I
66(C5,3,0) T_FM_ST_GAIN_I
67(C6,3,6) T_READ_BATT_I
68(C8,0,3) T_VBATT1_I
69(C9,0,3) T_VBATT2_I
70(CA,3,0) T_WRITE_BATT_I
71(D1,3,0) T_CDMA_TXADJ_I
72(D2,3,0) T_FM_TXADJ_I
73(D3,1,0) T_SET_PA_R0_I
74(D4,4,0) T_OFF_PA_R0_I
75(D5,0,3) T_READ_RSSI_I
77(D7,0,3) T_READ_TEMP_I
78(D8,0,3) T_RXRAS_AUTO_I
79(D9,1,0) T_BUZZER_ON_I2)
80(DA,0,0) T_BUZZER_OFF_I
5-9
2)
2)3)
2)3)
2)3)
2)3)
2)3)
2)3)
2)3)
1)
3)
3)
3)3)
2)
2)
2)
3)
SAMSUNG Proprietary-Contents may change without notice
Description
Vocoder CDMA unity gain.
Vocoder FM hfrx upgain.
Activate dtmf generator with keycode.
Deactivate DTMF generator.
Enable the compressor and expandor.
Diable the compressor and expandor.
Enter Analog voice channel state.
FM audio gain.
Active A Vibrator.
Inactive A Vibrator.
Batt type.
BBA supplier.
HW version.
Target Carrier option (Banner).
Target Service option (8K/13K).
External Audio Path ON/OFF.
Loopback ON.
Mic path on.
Mic path off.
Set Rx Path, TX Path Unmute to Earpiece.
FM Tx Audio Gain Control.
FM Rx Audio Gain Control.
FM Tx DTMF Gain control.
FM Tx Limiter Gain Control.
FM Tx SAT level Control.
FM Tx Master Gain Control.
FM TX ST Gain Control.
Reads low batt. Value in Standby or Talk mode.
Set the low battery position in the standby.
Set the low battery position in the talking.
Write low battery Level Value to NVM.
Change pdm TX AGC in CDMA.
Change pdm TX AGC in FM.
Set TX power Amp ctrl R0.
Off TX power Amp ctrl R0.
Read a RSSI.
Read Temp.
Adjust RXRAS from 8924C.
Buzzer On at DTMF 0 key
Buzzer off