Related Manuals for Standard Horizon MD150
Summary of Contents for Standard Horizon MD150
- Page 1 MD150 Digital Multi-Data Instrument Owner’s Manual Marine Division of Vertex Standard...
-
Page 2: Limited Warranty
To obtain warranty service, the defective product must be returned to STANDARD HORIZON together with proof of the date of purchase. The Purchaser must pay any transportation expenses in returning the product to STANDARD HORIZON. STANDARD HORIZON will examine the product and respond to the Purchaser in approximately four (4) weeks from date of receipt of the product claimed to be defective. -
Page 3: Table Of Contents
5.13.2 Transducer Setting ..................12 5.13.3 Speed Calibration ................... 12 5.13.4 Calibrate Temperature Display ............... 12 5.14 Simulation Mode ..................12 6 Maintenance ...................... 13 7 Specifications ....................13 8 Troubleshooting ....................14 MD150 User Manual Page 3 Owner’s Manual... -
Page 4: General Information
Note: Please familiarize yourself with the entire manual and transducer installation guide before attempting installation. 1.1 Introduction 1.2 Front panel The MD150 is a stand-alone, multidata instrument The front panel includes a a multi-function LCD and which displays depth, speed, temperature, log and four-button keypad. The keypad uses both tactile time functions. -
Page 5: Accessories
DST55 ........................In-hull Depth Transducer FB52 ........................Fairing block for DST52 3.2 Replacement Parts The following parts may be ordered from the STANDARD HORIZON Parts Department. To order, call: 562-404-2700 Ext 351 Part ............................Part Number Dummy Plug, SIA53 ........................356002017A Dust Cover ............................ -
Page 6: Wiring Connection
If you are not using a repeater of you do not Transducers intend to provide NMEA data to another instrument then insulate the bare end of the Figure 3. Wiring Connections blue wire. Page 6 MD150 User Manual Owner’s Manual... -
Page 7: Multiple Instruments
4.4 Multiple Instruments The MD150 may be used as an individual instrument 4.5.2 In-Hull Installation or connected with a number of other 150 series Transducer installation inside a solid fiberglass hull instruments to the 150 series repeater, STANDARD may degrade performance of depth sounder. -
Page 8: Changing Functions
The new unit of measure will be TRIP DISTANCE displayed for three seconds. Depth units can be selected in the following order; meters, feet and fathoms. Page 8 MD150 User Manual Owner’s Manual... -
Page 9: The Depth Alarms
ELAPSED TIME Use the keys to set alarm value. Press and hold the keys for three seconds to reset the elapsed time to zero. 3 SEC Press the key to exit. MD150 User Manual Page 9 Owner’s Manual... -
Page 10: Count Down Timers
Repeat this procedure to turn the lighting off. To reset the count down timer, press and hold the keys for three seconds while the countdown timer is displayed. The display will return to the timer selection. Page 10 MD150 User Manual Owner’s Manual... -
Page 11: Secondary Functions
Note: If the speed and depth readings flash, this indicates that the calibration values have been lost. To correct this, check the depth units, alarm values, keel offset, speed units and the speed calibration. MD150 User Manual Page 11 Owner’s Manual... -
Page 12: Keel Offset
5.13.1 Keel Offset 5.13.3 Speed Calibration The MD150 will normally display the depth of water Use the following sequence to adjust the speed below the face of the transducer. You may introduce displayed to match that of another craft or the a keel offset to display the depth of water below the speed displayed on a GPS receiver. -
Page 13: Maintenance
(depending on transducer type). User NMEA and power. selectable to display in 0.1 or 0.01 increments. Speed units and resolution • 0.0 to 19.9 and then 20 to 50 in knots, MPH or KPH. MD150 User Manual Page 13 Owner’s Manual... -
Page 14: Troubleshooting
Add alternator whine filter to alternator. • At power up, if all the segments display for 5 c. Replace spark plug with resistive type. seconds then the instrument is in simulation mode. Page 14 MD150 User Manual Owner’s Manual... - Page 15 MD150 User Manual Page 15 Owner’s Manual...
- Page 16 Marine Division of Vertex Standard 17210 Edwards Road Cerrtios, CA 90703 M32385104A Telephone: 562/404-2700 STANDARD HORIZON ALL RIGHTS RESERVED PRINTED IN NEW ZEALAND 1950751A FEBRUARY 2001 MN000017...
Need help?
Do you have a question about the MD150 and is the answer not in the manual?
Questions and answers