Features At A Glance Temperature Controls First Steps Helpful Hints Beverage Center Extra Features Optional Ice Service Energy Saving Tips Vacation and Moving Tips Normal Operating Sounds Care & Cleaning Warranty Information Troubleshooting Before You Call 8-12 17-18 20-21 P/N 241666500 (0905)
Junked or abandoned refrigerators or freezers are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator or freezer, please follow the instructions below to help prevent accidents.
This Use & Care Manual provides specific operating instructions for your model. Use this beverage center only as instructed in this Use & Care Manual. Before starting this beverage center, follow these important first steps. LOCATION • Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.
INSTALLATION - CONNECTING ICE MAKER TO WATER SUPPLY WARNING WARNING WARNING WARNING WARNING To avoid electric shock, which can cause death or severe personal injury, disconnect the beverage center from electrical power before connecting a water supply line to the beverage center. CAUTION CAUTION CAUTION...
Ice Maker (Accessory) Ice Bucket (Accessory) Freezer Shelf Air Flow Control Temperature Control Features may vary according to model Shelf Tower Keg Support Shelf COOL DOWN PERIOD To ensure safe food storage, allow the beverage center to operate with the doors closed for at least 12 hours before loading it with food and beverages.
This Use and Care Manual provides specific assembly, operating and maintenance instructions for your model. Use the beverage center only as instructed in this Use and Care Manual. Before starting the beverage center, follow these important first steps. PARTS Your beverage center comes with a box that contains all the required parts and accessories.
FAUCET ASSEMBLY INSTALLATION • Attach faucet knob (9) to Faucet & Shank Assembly (6). • Slip the Faucet & Shank Assembly (6) through the black plastic collar (7) (flat side toward door), Facade (3), and hole in door. • Thread on the large Shank Nut (8) and tighten until snug, using an adjustable wrench.
BRAIDED HOSE TO REGULATOR CONNECTION • Slip one Worm Clamp (14) onto braided hose (13). • Attach that end of the braided hose (13) to the hose barb of the CO regulator (10). Push hose up until seated against hex head. •...
DELIVERY HOSE PRESSURIZATION • Open the CO canister valve all the way by turning counterclockwise until it stops. This valve seals at both the fully open and fully closed positions. Failure to completely open or close the valve could result in premature loss of pressure.
DELIVERY HOSE ARRANGEMENT • Insert the clear hose (12) (delivery hose) into the hose routing clips attached to the door and the cabinet. Follow the hose routing shown below depending on the door swing direction of your door. Left Hand Swing Right Hand Swing CAUTION CAUTION...
If you’d like to make your beverage center so it can be rolled from room to room, there is an optional caster kit available from your authorized Frigidaire dealer or service center. Just ask for part number Kit, which includes 2 fixed casters, 2 swivel casters, 2 caster Canister) support rails and mounting hardware.
If your beverage center has an automatic ice maker, it will provide a sufficient supply of ice for normal use. However, during the initial startup of your beverage center, no ice will be produced during the first 24 hours of operation. Automatic ice makers are also optional accessories that may be installed in most models at any time.
ENERGY SAVING TIPS • Install the beverage center in the coolest part of the room, out of direct sunlight and away from heating ducts or registers. Do not place the beverage center next to heat-producing appliances such as a range, oven, or dishwasher. •...
UNDERSTANDING THE SOUNDS YOU MAY HEAR Your new high-efficiency beverage center may make unfamiliar sounds. These are all normal sounds and soon will become familiar to you. They also indicate your beverage center is operating as designed. Hard surfaces, such as vinyl or wood floors, walls, and kitchen cabinets may make sounds more noticeable.
Keep your beverage center clean to prevent odor build-up. Wipe up any spills immediately and clean both sections at least twice a year. Never use any type of scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any surface. Do not wash any removable parts in a dishwasher.
PROPER CLEANING OF BEVERAGE CENTER DISPENSING SYSTEM Your beverage center’s beverage dispensing system needs regular cleaning and sterilization in order to continue serving draft beer with its pure brewery flavor. It is recommended that the delivery lines be cleaned weekly and the entire delivery system cleaned before a new keg is attached.
BEVERAGE CENTER WARRANTY Your beverage center is protected by this warranty WARRANTY PERIOD FULL ONE-YEAR One year from Pay all costs for repairing or replacing any parts of this WARRANTY original purchase appliance which prove to be defective in materials or date.
Before calling for service, review this list. It may save you time and expense. This list includes TROUBLESHOOTING common occurrences that are not the result of defective workmanship or materials in this GUIDE appliance. PROBLEM BEVERAGE CENTER OPERATION • Beverage center is plugged into a circuit Beverage center does not that has a ground fault interrupt.
• Exchange keg for fresh one. • Wash glasses using soap-free detergent. • Clean faucet with recommended cleaning kit. • Remove items from atop keg and place in a separate refrigerator. supply line to keg until keg is...
Common Occurrences Beverage center does not run. Freezer temperature too cold. Refrigerator temperature is satisfactory. Refrigerator temperature too cold. Freezer temperature is satisfactory. * Beverage center is noisy or vibrates. Odors in beverage center. Cabinet light not working. Automatic ice maker not working.