Table of Contents
Advertisement
Using advanced features
Play the tape automatically
This feature allows the VCR to automatically start playing when you insert a tape with the safety tab
removed.
Press [SETUP] button and select
1
1
"FUNCTIONS".
Move
into "FUNCTIONS" with [ ] and
then, select the desired one with [ENTER]
button.
Press [ENTER] to switch between ON
2
2
and OFF.
- Select ON if you want a tape with its safety
tab removed to start playing automatically
when the tape is inserted.
- Select OFF if you do not want a tape with
its safety tab removed to start playing
automatically.
Switch the VCR to TV or VCR mode automatically
This feature controls whether the TV/VCR switch changes automatically to the VCR mode when the VCR is turned on.
Press [SETUP] button and select "FUNCTIONS".
1
1
Move
into "FUNCTIONS" with [ ] and then, select the desired one with
[ENTER] button.
Press [ENTER] to switch between ON
2
2
and OFF.
- Select ON if you want the VCR to switch to
the VCR mode when the VCR is turned on or
a cassette is inserted. This only applies if
you connect the ANT.IN and RF OUT jacks
of your VCR and TV and watch your VCR on
channel 3 of your TV.
- Select OFF if you want the VCR to remain in
the TV mode. This is useful if you watch
your VCR on the TV's video input and you
don't want your antenna/cable signal
interrupted by the VCR.
26
Searching a cassette tape for programs (indexing)
SETUP
CLOCK SET
TIMER RECORDINGS
CHANNEL SET
overlap, the index
FUNCTIONS
mark for the second
LANGUAGE SELECT
program will be
erased. Therefore,
Move:
Select:
ENTER
End:
SETUP
when you use the
index feature to find
the second program,
FUNCTIONS
the VCR will skip
Auto Play:
ON
over it.
Auto TV/VCR:
ON
Index Search
• If you record
Go-To Search
multiple programs
in one recording
Move:
Select:
ENTER
session, the VCR will
End:
SETUP
only find the index
mark that was
placed on the video
cassette tape when
the recording
session began.
Searching with the tape counter (go- to search)
be missed by the VCR :
• A mark too close to
your location on the
FUNCTIONS
tape.
Auto Play:
ON
• The mark at the
Auto TV/VCR:
ON
beginning of a
Index Search
recorded segment of
Go-To Search
five minutes or less.
• The first index mark
Move:
Select:
ENTER
End:
SETUP
on the tape when
you start at the
beginning of the
tape.
Marking a tape for zero search
When you record a programs, the VCR places an index mark at the start of the recording. To search for an
index mark:
• If two
Press [SETUP] button and select
1
1
recordings
"FUNCTIONS".
Select "Index Search".
If you want to search through a certain number
2
2
of index marks, press two number buttons to
enter the number of marks you want to search.
Press CLEAR on the remote to correct an entry.
or
Press REW to search backward or FF to search
forward. The VCR will locate your index mark
and begin playback. If you did not enter a
specific index number, the VCR will locate the
next index mark and begin playback. Press STOP
to stop index searching.
You can mark a segment of the video cassette with the tape counter that will help you easily locate the
segment later.
Some index
Press [SETUP] button and select
1
1
marks that may
"FUNCTIONS".
Select "Go-To Search".
The tape counter is displayed on the screen.
2
2
Input the tape counter you want to go and
press REW or FF, the VCR will search for the
time counter you want.
1
1
Use PLAY, REW,or FF to reach the point on the tape that you would like to mark as
0:00:00.
2
2
Press [DISPLAY] button to display the tape counter on the screen.
3
3
Press [CLEAR] button to reset the tape counter to 0:00:00.
4
4
You can continue to play the tape or perform other functions with the VCR.
Using advanced features
FUNCTIONS
Auto Play:
ON
Auto TV/VCR:
ON
Index Search
Go-To Search
INDEX SEARCH
Press REW or FF
to begin searching
or
Enter a specific
index number
- -
End:
SETUP
FUNCTIONS
Auto Play:
ON
Auto TV/VCR:
ON
Index Search
Go-To Search
GO-TO SEARCH
Current tape counter is
2 : 17 : 18
Press REW or FF
to go to - : - - : 00
27
Advertisement
Table of Contents
