Table of Contents
Advertisement
Available languages
Available languages
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Skil MAG77LT
Summary of Contents for Skil MAG77LT
-
Page 2: General Power Tool Safety Warnings
General Power Tool Safety Warnings Read all safety warnings and all instructions. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE Work area safety power tool. Do not use a power tool while you are tired or under the influence of drugs, Keep work area clean and well lit. -
Page 3: Safety Rules For Circular Saws
Disconnect the plug from the power source Keep cutting tools sharp and clean. and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Use the power tool, accessories and tool bits etc. in accordance with these instructions, Store idle power tools out of the reach of taking into account the working conditions children and do not allow persons unfamiliar... - Page 4 This circular saw should not be mounted to Do not use dull or damaged blades. a table and converted to a table saw. Blade depth and bevel adjusting locking Kickback causes and related levers must be tight and secure before warnings making cut.
-
Page 5: Additional Safety Warnings
Always observe that the lower guard is covering the blade before placing saw down on bench or floor. Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced Do not run the tool while carrying it at your before use. - Page 6 Symbols IMPORTANT: Symbol Name Designation/Explanation...
- Page 7 Symbols (continued) IMPORTANT:...
-
Page 8: Functional Description And Specifications
Functional Description and Specifications Disconnect the plug from the power source before making any assembly, adjustments or changing accessories Circular Saws Maximum Capacities NOTE:... -
Page 9: Attaching The Blade
Assembly ATTACHING THE BLADE Disconnect the plug from the power source before making any assembly, adjustments or changing accessories VARI-TORQUE CLUTCH... -
Page 10: Depth Adjustment
Operating Instructions DEPTH ADjUSTMENT 90° CUTTING ANGLE CHECK BEVEL ADjUSTMENT LINE GUIDE °... - Page 11 MAXIMUM DEPTH OF CUT STABILITY ADjUSTMENT Note WRENCH USAGE...
-
Page 12: Plunge Cuts
SWITCH released, be aware of the necessary time it When starting the tool, takes for the blade to come to a complete hold it with both hands. stop during coast down. Do not allow the saw to brush against your leg or side, since the lower guard is retractable, it could catch on your clothing and expose the blade. -
Page 13: Cutting Large Sheets
CUTTING LARGE SHEETS RIP CUTS RIP BOARD GUIDE... -
Page 14: Maintenance
Maintenance To avoid accidents always disconnect the tool from the power supply before cleaning or performing any maintenance. Service CARBON BRUSHES Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. -
Page 15: Care Of Blades
CARE OF BLADES TWIST-TO-LOCK CONNECTOR INSTRUCTIONS FOR MODEL MAG77LT CODE 72 ONLY 20 AMP, 125 VOLT “TWIST-TO-LOCK” Extension Cords If an extension cord is RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS necessary, a cord with adequate size conductors that is capable Wire Sizes in mm Cord Size in A.W.G. -
Page 16: Troubleshooting
Trouble Shooting TROUBLE: SAW WILL NOT START PROBLEM REMEDY TROUBLE: BLADE DOES NOT COME UP TO SPEED PROBLEM REMEDY TROUBLE: EXCESSIVE VIBRATION PROBLEM REMEDY TROUBLE: CANNOT MAKE SQUARE CUT WHEN CROSSCUTTING PROBLEM REMEDY TROUBLE: CUT BINDS, BURNS, STALLS MOTOR WHEN RIPPING PROBLEM REMEDY TROUBLE: BLADE SLIPPING... - Page 25 0°...
- Page 40 0°...
- Page 47 Notes: Remarques : Notas...
- Page 48 1619X04759...
Need help?
Do you have a question about the MAG77LT and is the answer not in the manual?
Questions and answers