Download Print this page

Advertisement

Next >>
<< Previous
Installing Your Multifunction
to Your Network for the First Time
PIXMA MX922
Macintosh OS
1

Advertisement

   Also See for Canon PIXMA MX922

   Related Manuals for Canon PIXMA MX922

   Summary of Contents for Canon PIXMA MX922

  • Page 1

    Next >> << Previous Installing Your Multifunction to Your Network for the First Time PIXMA MX922 Macintosh OS...

  • Page 2

    << Previous Next >> Installing Your Multifunction to Your Network for the First Time PIXMA MX922 Macintosh OS Preparing to Connect My Multifunction to My Network Network Requirements Notes on Wireless Connection Installing the Drivers...

  • Page 3

    Preparing to Connect My Multifunction << Previous Next >> To My Network Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Wireless Connection Before connecting the machine to the network, the computer needs to be connected to the network.

  • Page 4

    Preparing to Connect My Multifunction << Previous Next >> To My Network An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Notes on Network Connection • The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment.

  • Page 5: Software Installation

    Setup CD-ROM during restarting. The installation resumes once your computer has restarted. • If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.

  • Page 6: Installing Drivers

    Installing the Drivers << Previous Next >> 1. Insert the CD-ROM into the computer. IMPORTANT If the USB cable is already connected, unplug it. If a message appears on the computer, click Cancel. 2. Double-click the [Setup] icon in the CD-ROM folder, then click [Download] in the subsequent window.

  • Page 7

    Installing the Drivers << Previous Next >> REFERENCE •When the CD-ROM folder does not open automatically, double-click the CD-ROM icon displayed on the desktop. •The screen below is displayed while downloading.

  • Page 8

    Installing the Drivers << Previous Next >> If you click [Cancel] while downloading, you will see the following screen. - If you click [No], you will return to the screen displayed while downloading. - If you click [Yes], the download is cancelled. In this case, the files under the download are deleted. When the download fails, the screen below is displayed.

  • Page 9

    Installing the Drivers << Previous Next >> When the download is complete, the screen below is displayed. Click [Next]. REFERENCE Select "Save a file for setting up the software again to the download folder after the installation is complete," and the file will be saved to the download folder.

  • Page 10

    Installing the Drivers << Previous Next >> You can perform the setup later using this file...

  • Page 11

    Connecting to the Wireless Network << Previous Next >> 4. Click Next to install the helper tool 5. In the subsequent screen, enter the administrator name and password. Then click [OK].

  • Page 12

    Connecting to the Wireless Network << Previous Next >> 6. Continue following instructions. Click Network 8. Follow any instructions and Click Connect to the Connection on Connection Method Selection Network when the Printer Setup window appears . 9. Follow any instructions. Pay particular attention to the 7.

  • Page 13

    Connecting to the Wireless Network << Previous Next >> 10. The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*. If a WPS access point is detected, the Push Button Method screen (shown below on left) will appear on the machine’s operation panel *Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the Stop button on the printer’s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown below)*.

  • Page 14

    Connecting to the Wireless Network << Previous Next >> For Standard setup only Select Standard setup on the Setup Procedure Selection screen (3-2) Continue to next page before proceeding any further with setup...

  • Page 15

    Connecting to the Wireless Network << Previous Next >> Follow On-screen instructions. When you get to Step 4-2 and later in Step 4-4 ( screens shown below) you will need to know SSID and password information* Step 4-4 Step 4-2 *Unless you are absolutely certain of this information, please continue to the next page for information on locating / verifying this information...

  • Page 16

    Connecting to the Wireless Network << Previous Next >> If you don't know your Access Point / Router name or SSID*, or the Passphrase or Network key for your wireless network, you can find this information during Standard setup using the Setup CD-ROM or the downloaded files (Mini Master Setup or Master Setup). *The terms 'SSID' and 'AccessPoint / Router' refer to a name used to identify the specific Access Point or Router.

  • Page 17

    Installing the Drivers << Previous Next >> 11. Continue to follow any instructions until the Setup Completion or Completion of Connection screen below is displayed. Network connection setting is complete. Click Next. Software will install. Continue to follow instructions until the Add Printer screen (shown on next page) appears.

  • Page 18

    12. Network setup is complete. Continue to follow any remaining On-screen instructions to install the software. On the Software Installation List screen, select any software to be installed. MP Drivers and Canon IJ Network Tool which are pre-selected are required for the printer to be able to be used over the network.

  • Page 19

    Installing the Drivers << Previous Next >> Add the Printer 1. Click Add Printer on the Add Printer Screen...

  • Page 20: Installing The Drivers

    -The computer is connected to the access point *CAUTION If you will be installing the Canon printer driver on Mac OS X and using the printer through a network connection, you can select [Bonjour] or [Canon IJ Network] in the [Add Printer] dialog.

  • Page 21

    Installing the Drivers << Previous Next >> 4. Click Next. 5. Click Next. Setup is complete Setup is complete. Click Next to finish the remaining information section.

Comments to this Manuals

Symbols: 0
Latest comments:
  • Marilyn Jan 09, 2017 11:41:
    How to connect wireless canon mx922 to iPad. I do not have the original install disk.
  • Jean Persigehl Jul 03, 2016 06:27:
    How Much Does This All Cost Me?
  • ravjyot May 29, 2016 03:40:
    how to scan from computer and how to forward from machine to computer
  • Mary May 08, 2016 09:56:
    How do I connect my Android phone to my mx22 printer. What cable do I need
  • Jean Pinnow Oct 04, 2015 05:26:
    I could not print the full 30 pages nor could I put them in documents for future reference. The printer works fine but I need not knowledge about the fax abilities.