Pair the Q2 with your Phone Wearing Your Q2 Changing the Ear Bud Stabilizing Ear Buds Use Your Voice to Control the Q2 Use Your Voice to Make Phone Calls Use Your Voice to Answer Calls Voice Commands Transferring your Phonebook Contacts to the Q2 ...
Page 4
Reconnecting to the Q2 Using 2 Phones with the Q2 (Multipoint) Which Phone is Used for Calls? Multiple Calls (Call Waiting)* Resetting the Q2 Troubleshooting Alternatives to Voice Control Specifi cations Help and Support Terms and Conditions ...
Multi-Function Button (MFB) Introduction Microphones Welcome to the BlueAnt Q2: the voice controlled smart Bluetooth headset for smartphone users. With the Q2 you can make outgoing calls and answer incoming calls using just your voice, Vol - and you will always know who is calling without...
Charge Your Q2 Your Q2 has been given an initial partial charge to get you started, but for best results we recommend you fully charge it using the supplied USB cable and adaptor. > You should charge the Q2 whenever it announces that the battery is Very Low.
1. Slide the hardware power switch across to turn the Q2 on and then put the Q2 in your ear. 2. If this is the fi rst time you have used the Q2 it will go straight to pairing mode. The voice prompts will start to talk you through the pairing process.
Page 8
Automatic Transfer Not Supported Some phones do not support automatic phonebook transfers. If this is the case on your phone the Q2 will announce that it cannot transfer the contacts automatically. “Manually Transferring your Phonebook Contacts to the Q2” on page 14...
Changing the Ear Bud Your Q2 is supplied with a choice of ear buds in different sizes so that you can choose the one that fi ts best. If you want to change the ear bud, remove the attached one by gently lifting it away from the Q2.
Use Your Voice to Control the Q2 The Q2 is voice controlled. Simply click the and wait for the Q2 to ask you to Say A Command. Then immediately say one of the voice commands loudly and clearly. Phone Commands...
> Call Back to call back the last call you received on the Q2. Use Your Voice to Answer Calls When the phone rings, wait for the prompt to ask you if you want to take the call, and then say Answer or Ignore.
Voice Commands When you want to do something, just click the MFB, wait for the Q2 to ask you to Say A Command, and then say one of the following commands: > Am I Connected? — The Q2 will check if your phone is connected, and attempt to connect if it is not.
Page 13
> LED Light — Turns the LEDs on or off. When the LEDs are set to off, they still light up when you turn the Q2 on or off, but will not fl ash at other times. > Update Phonebook —...
Transferring your Phonebook Contacts to the Q2 Your Q2 uses Text to Speech technology (TTS) to read out the name of the person who is calling you. To do this, the Q2 needs to store a copy of your phonebook contacts.
Note: some phones do not support phonebook transfers at all. If this is the case, the Q2 will read out the caller’s number instead (providing your phone and carrier support caller ID). Updating your Phonebook Contacts on the Q2 If you add or change entries in your phonebook then you need to update the contacts on your Q2 by doing the following.
Reconnecting to the Q2 If you take your phone out of range of the Q2 for more than 2 minutes, the Q2 will go into “sleep mode” to save battery. When you bring your phone back into range, simply click the...
Depending on your phone, this may take a few seconds. Please ensure that Bluetooth is enabled on your phone. Using 2 Phones with the Q2 (Multipoint) Up to 2 devices can connect to the Q2 at the same time. If either phone rings, you can answer it with the Q2. Use the Pair Me command to put your Q2 back into pairing mode to pair another phone.
Note: Only the primary phone can play music through the Q2 via A2DP. Multiple Calls (Call Waiting)* If you receive an incoming call while you are already on a call the Q2 will play a tone to alert you. >...
If you are having problems with the Q2, you can reset it and start again. Resetting the Q2 will clear all the stored pairing settings on the Q2, delete any stored contact details and put the device back into pairing mode.
Bluetooth profi les, then you will not be able to copy your contacts to the Q2. When you receive a call, the Q2 will read out the caller’s number instead (providing your phone and carrier support caller ID).
Page 21
Update Phonebook command to update the contacts on your Q2. * Some phones do not allow you to adjust the order. If this is the case the Q2 will read the names in whatever order it receives from the phone.
Page 22
The Q2 Reads Out the Wrong Name If the Q2 is reading out the wrong name then it is likely that you have changed the contacts in your phone without updating the contacts on the Q2. If you make any changes to your...
Page 23
> Say your command as soon as possible after the Q2 asks you to Say A Command. > When you have an incoming call, you must wait for the Q2 to fi nish asking you if you want to...
> Try changing the Q2’s sensitivity level. This setting determines how precisely the words that you say need to match the speech patterns that the Q2 has been confi gured to recognize. You can change it by using the Sensitivity Level command.
Page 25
Q2 Function Do This When Update phonebook Hold the Q2 must be connected to your phone but about 3 seconds not on a call. Answer a call Click the Phone ringing. End a call Click the During an active call.
If you are having trouble getting the Q2 to work, please visit www.blueantwireless.com online help, support, and troubleshooting tips. Please contact us before returning the Q2 to a store and we will help you through any diffi culty you may have.
Bluetooth SIG, ® Inc. and any use of such marks by BlueAnt Wireless is under license. Android is a trademark of Google Inc., Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.