Avocent MergePoint SP5324 Quick Installation Manual page 2

MergePoint
QUICK INSTALLATION GUIDE
9 Confi guring the DSView 3 software
If you wish to host service processors on multiple
subnets, you can confi gure them through the DSView 3
software or MergePoint SP manager web interface. See
the installer/user guide for details.
(Optional) Adding the MergePoint SP manager
10
to the DSView 3 management software
Use the DSView 3 Add Units Wizard to begin managing
MergePoint SP managers with the DSView 3 software.
See the DSView 3 help (keywords: adding units) and the
MergePoint SP53XX appliance plug-in documentation for
more information.
MERGEPOINT APPLIANCE SAFETY AND
EMC NOTIFICATIONS
USA
WARNING: Changes or modifi cations to this unit not
expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial environ-
ment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to
correct the interference at his own expense.
Canada
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Japan
Technical support and fi rmware or software updates:
Product manuals: www.avocent.com/manuals
Avocent, the Avocent logo, MergePoint and DSView are registered trademarks of Avocent Corporation or its affi liates in the U.S. and other countries. All other marks are the property of their respective owners. ©2008 Avocent Corporation.
®
SP5324/SP5340
Service Processor Manager
Safety and EMC Approvals and Markings
USA (FCC), Canada (CSA), Australia (C-tick), European
Union (CE), Japan (VCCI)
Safety Precautions
Certifi cations for this product are obtained under one or
more of the following designations: CMN (Certifi cation
Model Number), MPN (Manufacturer's Part Number) or
Sales Level Model designation. The designation that is
referenced in the certifi cations reports and/or certifi cates
are printed on the label applied to this product.
DANGEROUS VOLTAGE
This symbol is intended to alert the user to the
presence of uninsulated dangerous voltage within
the product's enclosure that may be of suffi cient magnitude
to constitute a risk of electric shock to persons.
NOTE: The AC inlet is the main power disconnect.
INSTRUCTIONS
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions.
WARNING: To reduce the risk of electric shock or damage
to your equipment:
– Do not disable the power grounding plug. The ground-
ing plug is an important safety feature.
– Plug the power cord into a grounded (earthed) outlet
that is easily accessible at all times.
– Disconnect the power from the switch by unplugging
the power cord from either the electrical outlet or the
appliance.
CAUTION: The MergePoint SP5324/SP5340 appliance
contains an internal battery that is used for the real time
clock. This battery is not a fi eld replaceable item, and
replacement should not be attempted by a user. If real time
clock errors occur and the battery is suspected, visit http://
www.avocent.com/support or contact the Avocent Technical
Support location nearest you.
www.avocent.com
WARNING: For Service Personnel Only - There is a risk of
explosion if the battery is replaced with an incorrect type.
Dispose of used batteries according to the manufacturer's
instructions.
NOTE: To comply with FCC and CE certifi cation require-
ments, use shielded cables when connecting target devices
to the Ethernet ports. Failure to observe compliance require-
ments makes the equipment no longer compliant.
Rack and Wall Mount Safety Considerations
• Elevated Ambient Temperature: If installed in a closed
rack assembly, the operation temperature of the
rack environment may be greater than room ambient.
Use care not to exceed the rated maximum ambient
temperature of the appliance.
• Reduced Air Flow: Installation of the equipment in
a rack should be such that the amount of airfl ow
required for safe operation of the equipment is not
compromised.
• Mechanical Loading: Mounting of the equipment in the
rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
• Circuit Overloading: Consideration should be given
to the connection of the equipment to the supply
circuit and the effect that overloading of circuits
might have on overcurrent protection and supply
wiring. Consider equipment nameplate ratings for
maximum current.
• Reliable Earthing: Reliable earthing of rack mounted
equipment should be maintained. Pay particular
attention to supply connections other than direct
connections to the branch circuit (for example, use of
power strips).
590-838-501C