Pioneer Elite N-30 Operating Instructions Manual page 22

10 Additional information
When a USB storage device is connected
Problem Check
USB storage device is not Is the USB storage device properly
recognized. connected?
Is the USB storage device connected
via a USB hub?
This is not a problem with this unit.
A USB storage device is The audio files are copyrighted.
connected and displayed,
but the audio files stored
on the USB storage
device cannot be played
The file format cannot be properly
back.
played back on this unit.
Much time is required to What is the USB storage devices
recognized the USB capacity?
storage device.
Power is not supplied to Does an error message appear in the
the USB storage device. front panel display?
No power is supplied if the power
consumption is too high.
When computer is connected via USB cable
Problem Check
Has the proper device driver been
When the
DIGITAL IN
installed on the computer?
port is connected to
USB
a computer via USB
cable, audio files on the
computer cannot be
played.
22
En
Remedy
Connect the device securely (all the way in).
This unit does not support USB hubs. Connect the USB
storage device directly.
Turn the power off then back on.
Some USB storage devices may not be recognized properly.
This unit only supports USB mass storage class devices.
Only the FAT16 and FAT32 file systems are supported. Other
file systems (ex. FAT, NTFS, etc.) are not supported.
This device does not support the use of external hard disc
drives.
Copyrighted audio files stored on a USB storage device
cannot be played back. Attempting to import music data
from a CD, etc., to a computer may cause the invocation of
copy protection, depending on the settings.
See the list of file formats that can be played back on this
receiver (page 25).
Some time may be required to load the data when large
capacity USB storage devices are connected (this could
take several minutes).
Turn the power off then back on.
Turn the power off, then disconnect and reconnect the USB
storage device.
Press FUNCTION to switch to the other mode, then switch
again to the USB mode. (When the input is switched back to
USB.)
Remedy
When using a USB cable to connect the unit's
DIGITAL IN
port to a computer in order to play audio files on the
USB
computer, the proper device driver must be downloaded
from the Pioneer website and installed on your computer.
Consult the Pioneer website for instructions on installing
the driver.
Problem Check
No sound is produced Are volume settings correct for the
when attempting to play OS and application program?
files on a computer.
Is the OS audio output set to MUTE?
Are multiple applications running
simultaneously?
Are volume settings correct for the
OS and application program?
Network
Problem Check
Cannot access to the The LAN cable is not firmly
network. connected.
The router is not switched on.
Cannot access to the Internet security software is currently
component or PC installed in the connected
connected via network. component.
The audio component on the network
which has been switched off is
switched on.
The component connected to the
network is not properly set.
There are no playable audio files on
the component connected to the
network.
Playback does not start. The component is currently
disconnected from this receiver or
the power supply.
The PC or Internet radio is The corresponding IP address is not
not properly operated. properly set.
The IP address is being automatically
configured.
Remedy
Raise the volume settings as required.
Cancel the MUTE setting.
Try closing applications that are not in use.
For audio device select "Pioneer USB Audio Device".
Remedy
Firmly connect the LAN cable (page 7).
Switch on the router.
There are cases where a component with Internet security
software installed cannot be accessed.
Switch on the audio component on the network before
switching on this unit.
If the client is automatically authorized, you need to enter
the corresponding information again. Check whether the
connection status is set to "Do not authorize".
Check the audio files stored on the component connected to
the network.
Check whether the component is properly connected to this
receiver or the power supply.
Switch on the built-in DHCP server function of your router,
or set up the network manually according to your network
environment (page 19).
The automatic configuration process takes time. Please
wait.