Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Patton electronics IM1/K
Summary of Contents for Patton electronics IM1/K
- Page 1 MODELS IM1/K and IM2RC/K G.703/G.704 QuikConnect™ and Rear Card Modules Part# 07MIM1/K-C SALES OFFICE Doc# 090131UC (301) 975-1000 Revised 08/01/00 TECHNICAL SUPPORT C E R T I F I E D (301) 975-1007 An ISO-9001 http://www.patton.com Certified Company...
-
Page 2: Table Of Contents
5.0 Installation................11 the installation or use of this product shall be deemed an acceptance 5.1 Installing the IM1/K of these terms by the user. In the event the user detects intermittent or 5.1.1 Changing QuickConnect Modules continuous product malfunction due to nearby high power transmitting 5.2 Installing the IM2RC/K and Front Function Card... -
Page 3: Radio And Tv Interference
1.2 RADIO AND TV INTERFERENCE All warranty and non-warranty repairs must be returned freight The Models IM1/K and IM2RC/K (K Module) generate and use prepaid and insured to Patton Electronics. All returns must have a radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause... -
Page 4: Features
Network Cable Span Clock/ Clock/ 2.2 GENERAL PRODUCT DESCRIPTION Data Data Data Clock/ The Patton Model IM1/K G.703/G.704 QuickConnect Module and 1095 Data V.35 Module K Module 1095 IM2RC/K Rear Card Module provide E1/Fractional E1 termination and (1095RC) (1095RC) extension capabilities to the Patton NetLink mDSL modems (1095/1095RC). -
Page 5: Network Extension Application
3.2 NETWORK EXTENSION APPLICATION Network Extension mode is used to extend nx64 -2.048Mbps The K Module features configuration capability via hardware G.703/G.704 service across a DSL link, providing an nx64 switches and jumpers. Sections 4.1 and 4.2 describe all switch and G.703/G.704 link at the remote site. -
Page 6: Jumper Configuration
DTE Rate for the mDSL Modems This section describes how to configure your mDSL modem for use with an IM1/K (Model 1095) or an IM2RC/K (Model 1095RC). To select the number of G.703/G.704 channels to be carried across the link, multiply the number of required channels by 64Kbps The K Module requires the 1095/1095RC to have software ver- and then set the DTE rate of the mDSL modem to that number. -
Page 7: Installing The Im1/K
Installing the New QuikConnect™ Module 1) Make sure the power switch is off. Leave the power cord This section describes how to install the IM1/K and IM2RC/K mod- plugged into a grounded outlet to keep the unit grounded. ules into your mDSL modems. Please refer to the section in this manu- 2) Hold the module with the faceplate toward you and align the al that describes your unit. -
Page 8: Network
5.3 MAKING INTERFACE CONNECTIONS RJ-48C Cable (8-Wire) The Patton K Module may be connected to G.703/G.704 ports using a single 120 ohm RJ-48C or a dual 75 ohm coax (BNC). The K Module G.703/G.704 Patton K Module rear panels and the location of these connectors are SIGNAL PIN# NETWORK SIGNAL... -
Page 9: Appendix A - Specifications
Once the Patton K Module is installed and configured, it should PATTON ELECTRONICS MODEL K MODULE operate transparently. Please refer to the base unit (i.e. Model 1095) SPECIFICATIONS user manual for instructions on how to read the front panel LEDs, per- form diagnostics, monitor system status, and connect to the DSL line port. -
Page 10: Appendix B - Cable Recommendations
Short Range Modem are tested to the distances published in our Catalogs and Specification Sheets on twisted-pair cable with the fol- 07MIM1/K Module ...K Module User Manual lowing characteristics: IM1/K Module ....K Module for use with Model 1095 IM2RC/K Module.....K Module for use with Model 1095RC Wire Gauge Capacitance Resistance IM1RC/K Module.....K Module flip card... -
Page 11: Appendix D - Dip Switches
DIP SWITCHES Figure A (below) shows the location of the DIP switches on top of Figure C (below) shows the top view of the IM1/K printed circuit the printed circuit board. Following Figure A, Figure B shows the ori- entation of the DIP switches on the printed circuit board.