Table of Contents
Advertisement
Specifications
Power supply:
DC 12 V
(when external power is supplied)
AC 150 V - 240 V
(when CCU is connected)
Power consumption: 28 W (during external power
supply operation, camera only)
34 W (when CCU is connected)
indicates safety information.
Ambient temperature range:
14 °F to 113 °F (–10 °C to +45 °C)
[Preheating required at temperatures
below 32 °F (0 °C)]
Storage temperature range:
–4 °F to 140 °F (–20 °C to +60 °C)
Operating ambient humidity:
Less than 85 %
Weight:
Approx. 10.36 lbs. (4.7 kg)
Dimensions:
5-5/16˝ 10-1/4˝ 14-3/16˝
(W H D)
(135 260 360 mm)
[excluding protrusions]
Basic items
1) Pickup device:
2/3˝ 2.2 million pixel IT-CCD 3
2) System:
GBR pickup system
3) Color separation optical system:
f/1.4 prism
4) Optical filters:
CC: 3200K, 4300K, 6300K, Cross,
Diffusion
ND: CAP, Through, 1/4, 1/16, 1/64
5) Lens mount:
Bayonet type
6) Output standard: SMPTE 292M
7) Sensitivity:
f/10.0, 2000 lux, 3200K,
white reflectance 89.9 %
(Vertical frequency: 59.94 Hz)
8) Horizontal modulation:
More than 50 % (27.5 MHz)
9) S/N ratio:
60 dB typ. (Y: 30 MHz)
10) Horizontal frequency:
33.716 kHz, 1125-line frame
(Vertical frequency: 59.94 Hz)
28.125 kHz, 1125-line frame
(Vertical frequency: 50 Hz)
11) Vertical frequency:
59.94 Hz or 50 Hz, interlace
Input/output signals
1) MIC input:
–60 dBu to +4 dBu
(XLR 3-pin female 2)
Gain selected by camera menu
2) INCOM:
Input: –60 dBu to –10 dBu
Output: 100 mW max.
(XLR, 5-pin female 2)
(Mixing is controlled separately for
PGM1 and PGM2.)
3) HD-SDI1/HD-SDI2 output:
HD signal = 0.8 Vp-p, 75 ohms (BNC)
The HD-SDI2 signal output can be
added to the regular images using the
camera menu item setting and switched
to the VF or RET image output.
4) Prompt output:
VBS signal = 1 Vp-p, 75 ohms (BNC)
G/L input:
Tri-level SYNC or black burst (BNC)
Selected using a switch.
5) AUX BNC
• HD RET input: HD analog signal = 1 Vp-p, 75 ohms
(BNC)
• Prompt2 output: VBS signal = 1 Vp-p, 75 ohms (BNC)
(When the CCU has a Prompt2 input)
• Down converter output (supported as an option):
VBS or D1 signal = 1 Vp-p or 0.8 Vp-p,
75 ohms (BNC)
Input or output can be selected using
the camera menu item setting.
6) DC OUT:
12 V, MAX. 1A
Control
1) Power selection: CCU, OFF, EXT
2) USER 1, 2, 3:
Functions specified by menu items can
be allocated to the switch.
3) RET A/B selection:
For selecting the return signal
4) Monitor selection: Y/C, NAM, R, G, B
5) RET, PTT SW:
RET, PTT
6) Gain selection:
LOW, MID, HIGH
7) Output selection: CAM, BAR, TEST
8) White balance mode:
A, B, preset
9) Shutter speed selection:
1/100, 1/125, 1/250, 1/500, 1/1000,
1/2000
10) AWB, ABB settings
11) Menu selection
12) CALL SW
13) INCOM:
MIC ON/OFF, receiving level or PGM
level
14) MIC setting:
MIC power, MIC gain, MIC1 selection
15) Optical filter setting:
REM, LOCAL selection and LOCAL
setting
16) Back light SW (rear panel):
ON/OFF
* When the CCU is connected, the selection functions
for 6) to 10) are not effective.
Control is exercised from the ROP or MSU.
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
42
Advertisement
Table of Contents
