Echo srm-400 42.7cc brushcutter parts catalog (44 pages)
Summary of Contents for Echo 99944200600
Page 1
Users of this equipment risk injury to themselves and others if the unit is used im- properly and/or safety precautions are not followed. ECHO provides an operator’s manual. It must be read and understood for proper and safe operation. Failure to do so could result in serious injury.
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the SAFETY MANUAL. You will find both easy to use and full of helpful operations tips and SAFETY messages.
PAS 80 T ooTh lAde rimmer TTAchmenT PerATor AnuAl afeTy WARNING Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling, starting and stop- ping instructions. manual safeTy symbols and ImporTanT InformaTIon Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre- ceded by symbols or key words.
Hot Humid Weather Hearing Protection Heavy protective clothing can increase operator fatigue ECHO recommends wearing hearing protection whenever which may lead to heat stroke. Schedule heavy work for unit is used. early morning or late afternoon hours when temperatures are cooler.
PAS 80 T ooTh lAde rimmer TTAchmenT PerATor AnuAl Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI).
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them. If a decal cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDERING...
4. BLADE - Circular blade for brush cutting applications. Harness, metal shield and U-handles required for blade operation. onTenTs After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. ___ 1 - Pro Attachment Series...
ssembly WARNING Do not perform maintenance or assembly procedures with engine running. Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling, Metal Shield, Bracket, Barrier Bar power head shafT aTTaChmenT lower shafT assembly 1. Set Power Head/Shaft Assembly on a level surface. Pull locator pin (A) and rotate counter clockwise 1/4 turn to lock out position.
PAS 80 T ooTh lAde rimmer TTAchmenT PerATor AnuAl InsTall handle barrIer bar NOTE The Barrier Bar is required when using grass or weed blades. Units equipped with U-Handles do not require installation of the Barrier Bar. 1. Remove screws and nuts and back plate from handle. 4-screw front handles 2.
balanCe unIT 1. Put on harness and attach unit to harness. 2. Slide harness clamp up and down until unit balances with head ap- proximately 2 - 3 in. from the ground. 3. Tighten clamp screw. 2 - 3" NOTE In case of Emergency, the trimmer/brushcutter can be released from the the harness by pulling up on the quick-release collar.
ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO dealer for repairs.
1. Insert small end of hook into locating hole on attachment shaft. 2. Slide plastic cap onto end of attachment shaft. peCIfICaTIons Model ------------------------------------------------------- 99944200600 Shaft Length ------------------------------------------------ 870 mm (34.3 in.) Attachment Width ----------------------------------------- 280 mm (11 in.) Attchment Height ------------------------------------------ 255 mm (10 in.) Weight (dry) w/blade -------------------------------------- 1.5 kg.
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your ECHO unit to an authorized ECHO servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been made.
Page 14
89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
Page 15
PAS 80 T ooTh lAde rimmer TTAchmenT PerATor AnuAl noTes...
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo- usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video. ECHO, INCORPORATED...