Table of Contents
Advertisement
F
e
a
t
u
r
e
s
O
F
e
a
t
u
r
e
s
O
Microphone:
Omni-directional microphone
with protective water-resistant cloth.
Faceplate: 18 guage 304 stainless steel or 16
gauge polished brass faceplate with super
durable UV stable powder paint to prevent
fading and resist scratching.
Speaker: Mylar speaker with rubber gasket to
maintain water-tight seal and eliminate water
deterioration.
Speaker Screen:
Stainless steel speaker
screen with 0.018" diameter holes to prevent
punctures from paperclips, etc.
Color Video Camera:
Wide operating
temperature range of -30°F to 150°F, NTSC
composite video output with 420 lines of
resolution, 70° wide viewing angle lens, tilt and
swivel adjustments for aiming towards visitors.
Protective Camera Window: Impact resistant
polycarbonate lens with scratch resistant
coating and water-tight gasket.
Mounting Screws: 6-32 x 1.25" long flathead
with 5/64" hexdrive, 18-8 stainless steel to
prevent corrosion.
I
n
s
t
a
l
l
a
t
i
o
I
n
s
t
a
l
l
a
t
i
o
The E-50 is designed to be flush mounted into a standard single gang rough-in box with minimum inside dimensions of 2.25" deep x 2.00"
wide x 2.84" tall. The E-50 can also be surface mounted in a Viking model VE-3x5 (not included, see DOD# 424).
WARNING: Do NOT use a typical "wet location box" as not all styles seal properly with the E-50 faceplate.
A. New Construction Flush Mounting
Step 1.
Recommended mounting height to bottom of the rough-in box is 50" - 54". Front of box should stick out approximately
½" from front surface of wall stud (this may vary depending on the walls sheathing and siding thickness). Caution:
Rough-In box must be mounted LEVEL and must NOT stick out beyond the front surface of siding.
Step 2.
To maintain a vapor barrier on outside wall applications, caulk around the box, filling any gaps between the box and the
rough opening. Apply caulk to any holes in the box around wires, etc.
Step 3.
When installing siding cut a hole just large enough for the Rough-In box opening. Caution: Too large of a hole can
cause plate misalignment and compromise the gasket seal. Note: When mounting to 4 inch or less horizontal lap
siding, the unit can be mounted horizontally (see page 5, section H) flush against siding or a siding mounting block
can be used (recommended with vinyl siding). Contact siding installer for the correct mounting block.
B. Old Work / Remodel Flush Mounting
Step 1.
Recommended mounting height to bottom of the rough-in box is 50" - 54". Make sure mounting location is free of wall
studs, wires, etc.
Step 2.
Place Rough-In box LEVEL against siding. Trace outline of box onto siding. Note: When mounting to 4 inch or less
horizontal lap siding, the unit can be mounted horizontally (see page 5, section H) flush against siding or a siding
mounting block can be used. Contact your siding Installer for the correct mounting block part number. Note: A siding
mounting block is recommended when mounting to vinyl siding.
Step 3.
Cut a hole through the siding and wall sheathing just large enough for the rough-in box. Caution: Too large of a hole
can cause plate misalignment and compromise the gasket seal.
Step 4.
The front surface of the Rough-In box can be mounted flush against wood siding or can be recessed and mounted
flush against wall sheathing when mounting on aluminum, steel or vinyl siding.
Step 5.
When mounting to 5/8 inch thick or less wall sheathing the two attached screws with wing brackets can be used to
secure the rough-in box. When mounting to surfaces thicker than 5/8 inch, four standard flat head dry wall screws can
be used to secure the Rough-In box through its mounting ears (see page 4 section D).
Step 6.
To maintain a vapor barrier on outside wall applications, caulk around the box, filling any gaps between the box and
the rough opening. Apply caulk to any holes in the box around wires, etc.
v
e
r
v
i
e
w
v
e
r
v
i
e
w
n
n
Blue LED: Helps locate the push button in dark
locations, indicates paging and off-hook conditions.
Push Button Switch:
disconnect. Solid 304 stainless steel internally sealed per IP67.
(Using a recommended Allied Molded 9331 Rough-In Box)
Faceplate Gasket:
thick closed cell PVC to
water-tight seal faceplate,
speaker,
switch
microphone.
Speaker Volume
Microphone Volume
Dip Switches:
1. Auto Answer
2. Dial Tone Detection
VIKING
3. Programming
4. LED On/Off
Entry
Phone
Board:
Compact analog speaker
phone with call progress
detection
for
automatic
disconnect.
Push to initiate call, push again to
1/4"
and
3
Advertisement
Table of Contents
