Allied Telesis AT-VP504E FXS User Manual
  1. Manuals
  2. Brands
  3. Allied Telesis Manuals
  4. VoIP
  5. AT-VP504E FXS
  6. User manual
Allied Telesis AT-VP504E FXS User Manual

Allied Telesis AT-VP504E FXS User Manual

Voiptalk
Hide thumbs Also See for AT-VP504E FXS:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Administration Manual, User Manual
AT-VP504E FXS (SIP/MGCP)
VoIPTalk
User's Manual
PN 990-11591-10 Rev C

Advertisement

Table of Contents
loading

Related Manuals for Allied Telesis AT-VP504E FXS

Summary of Contents for Allied Telesis AT-VP504E FXS

  • Page 1 AT-VP504E FXS (SIP/MGCP) VoIPTalk User’s Manual PN 990-11591-10 Rev C...
  • Page 2 Copyright © 2001 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.

  • Page 3: Table Of Contents

    Contents User’s Manual (SIP/MGCP Version) Contents Chapter 1 Using the AT-VP504E FXS ..............1 Before you Begin ......................1 Acronyms..........................2 Overview of the AT-VP504E FXS.................... 2 Using the AT-VP504E FXS ..................... 3 Call Processes......................3 Calls Involving Another Terminal ..................... 4 Calls Involving a Terminal and a LAN Endpoint ..............
  • Page 4 Contents User’s Manual (SIP/MGCP Version) AT-VP504E FXS...

  • Page 5: Using The At-Vp504E Fxs

    This manual illustrates some of the various call processes the AT-VP504E FXS supports. It also describes how to make and receive calls, as well as how to use the services the AT-VP504E FXS offers. Before you Begin This manual assumes that:...

  • Page 6: Acronyms

    (4) analog terminals to a LAN with access to an IP Network, allowing high-quality, full duplex, audio/fax communication. This version of the AT-VP504E FXS can use either one of the following signalling protocol: the Session Initiation Protocol (SIP), which is a simple 2.

  • Page 7: Using The At-Vp504E Fxs

    Voice over IP (VoIP) Gateways from intelligent external call control elements. Using the Now that your administrator has properly set up the AT-VP504E FXS AT-VP504E and IP Communication Server configuration settings, you can dial any number on your phone (which is connected to the AT-VP504E FXS) and place the call.

  • Page 8: Calls Involving Another Terminal

    The following example illustrates how to reach a phone or fax on Another Termi- another AT-VP504E FXS terminal. Phone/Fax -> AT-VP504E FXS A -> AT-VP504E FXS B -> Phone/Fax A user makes a call with the phone/fax connected to an AT-VP504E FXS, which in turn contacts another AT-VP504E FXS, then reaches the corresponding phone/fax.

  • Page 9: Calls Involving An Analog Gateway

    IP Communication Server Calls Involving The following example illustrates how a telephone/fax connected to an an Analog AT-VP504E FXS terminal and a SCN phone can communicate via an Gateway analog gateway. Phone/Fax -> AT-VP504E FXS -> AT-VP504E FXO (Gateway) ->...
  • Page 10 (Gateway) IP Communication Server Calls Without a SIP Server If the AT-VP504E FXS is not configured to register with a SIP Server you can make SCN to IP network calls by dialing an IP address. IP Address Call You can dial another communication unit (gateway or terminal) without the help of a SIP Server by entering its IP address.

  • Page 11: Making Calls

    Chapter 1 - Using the AT-VP504E FXS User’s Manual (SIP/MGCP Version) Making Calls Users that have telephones or faxes connected to an AT-VP504E FXS will dial as if they were on a standard telephony system. Complete Dial- There are three ways to indicate the dialed number sequence is...

  • Page 12: Dialing An Ip Address

    Address Communication Server by entering its IP address. You will only be able to reach the phone or fax connected to Port 1 of this AT-VP504E FXS This procedure will only work if your AT-VP504E FXS is running the SIP signalling protocol. See your network administrator for more details.

  • Page 13: Using The Call Waiting Feature

    Chapter 1 - Using the AT-VP504E FXS User’s Manual (SIP/MGCP Version) ***192*168*0*23# Using the Call The call waiting feature allows you to put a call on hold. For instance, if you are already on the phone and a second call happens, a “beep”...

  • Page 14: Call Transfer - Supervised

    Chapter 1 - Using the AT-VP504E FXS User’s Manual (SIP/MGCP Version) Call Transfer – The call transfer – supervised allows you to transfer a current call to Supervised any other extension or phone number. However, the individual at the other extension or phone number must answer to complete the transfer.

  • Page 15: Using The Call Forward Feature

    Chapter 1 - Using the AT-VP504E FXS User’s Manual (SIP/MGCP Version) If you want to get back to the first call (the call on hold), you must perform two Flash Hooks. You are back with the first call and the third party is released.

  • Page 16: Call Forward On Busy / No Answer

    Chapter 1 - Using the AT-VP504E FXS User’s Manual (SIP/MGCP Version) To check if the call forward has been properly established: Take the receiver off-hook. Wait for the dial tone. Dial your extension or phone number. The call is forwarded to the desired phone number.

  • Page 17: Conferencing Calls

    Chapter 1 - Using the AT-VP504E FXS User’s Manual (SIP/MGCP Version) Conferencing A conference call between three parties can be set up. Calls Requirements For the conference call to occur succesfully, all parties must meet the following requirements: µ Support at least one of the PCM codecs (G.711 -law and G.711 A-law) enabled on the port that is having the...
  • Page 18 Chapter 1 - Using the AT-VP504E FXS User’s Manual (SIP/MGCP Version) A wants to terminate the call with C and get back to the call with B during the conference: A performs a Flash-Hook. The conference is terminated and the call with C is disconnected.

  • Page 19: Appendix A Glossary

    In this context, the Area Code corresponds to the Z portion of the numbering plan. Since virtually every country has a different dialing plan nomenclature, it is recommended to identify the equivalent of an Area Code for the location of your device. AT-VP504E FXS...
  • Page 20 (for example, between the packet network and the Public Switched Telephone Network). IP Acronym for Internet Protocol. The IP protocol is a standard describing software that keeps track of the Internet’s addresses for different nodes, routes outgoing messages, and recognises incoming messages. AT-VP504E FXS...
  • Page 21 Windows NT Server. Session Initiation SIP is a simple signaling protocol for Internet conferencing and Protocol (SIP) telephony. Single Network SNMP is the protocol governing network management and the Monitor Protocol monitoring of network devices and their functions. (SNMP) AT-VP504E FXS...
  • Page 22 Internet Protocol. Such data network may be the Internet or a corporate Intranet. Wide Area Network A computer network where the computers are not geographically close (WAN) and are linked by telephone lines or radio waves. AT-VP504E FXS...
  • Page 23 Server 17 SIP 17 SNMP 17 Flash-Hook 16 FXS Line 16 T.38 18 TCP/IP 18 telephone number, dialing 7 Gateway 16 TFTP 18 transferring a call supervised 10 unsupervised 10 hold, putting a call on 9 VoIP 18 AT-VP504E FXS...
  • Page 24 Index User’s Manual (SIP/MGCP Version) AT-VP504E FXS...

Table of Contents