Advertisement
Quick Links
Download this manual
See also:
Installation Manual
The AP60/61
Mounting Kit Installation Notes
The AP60-MNT can be used to attach an AP60 or AP61 Access
Point (AP) to a shelf, wall, post, ceiling, or partition hanger. The
included mounting cradle holds the AP firmly in place when
installed, and also allows for quick release when maintenance is
required.
These Installation Notes provide instructions for using the
mounting kit and modify information found in the AP60/61
Wireless Access Point Installation Guide. Please keep this
information with your Wireless Networks documentation.
Kit Components
The following items are included in the AP60-MNT:
F
IGURE
1 AP60/61 Mounting Kit Packing List
The AP60/61 Mounting Kit Installation Notes
ad
Cross-head
Nut
w
Screw
15/16"
T-Rail Clip
Label
9/16"
Cover
T-Rail Clip
1
Advertisement
Related Manuals for Alcatel AP60
Summary of Contents for Alcatel AP60
- Page 1 The AP60/61 Mounting Kit Installation Notes The AP60-MNT can be used to attach an AP60 or AP61 Access Point (AP) to a shelf, wall, post, ceiling, or partition hanger. The included mounting cradle holds the AP firmly in place when installed, and also allows for quick release when maintenance is required.
- Page 2 Mounting the AP Cradle The mounting kit can be used to install the AP60/61 in a variety of ways, each of which is detailed in the following sections: On a solid wall, shelf, or ceiling surface (see...
- Page 3 (not included) as shown above. —Do not use screws to attach the mounting cradle to a AUTION suspended ceiling or other structurally weak surface. For suspended ceilings, use the T-rail clips as described on page The AP60/61 Mounting Kit Installation Notes...
-
Page 4: Suspended Ceiling Mount
AP60-MNT: Installation Notes Suspended Ceiling Mount The mounting kit can be used to hang the AP from an indoor suspended ceiling. 1. Attach the T-rail clips to the ceiling rail. 3 Attaching the T-Rail Clips IGURE The T-rail clip twists onto the ceiling rails used with standard suspended-ceiling systems. - Page 5 2. Attach the cradle to the T-rail clip. Bolt Hole Side View T-Rail Clip Cradle 4 Mounting the Cradle to a Suspended Ceiling IGURE 3. Place the nut on the T-rail clip bolt to secure the cradle. The AP60/61 Mounting Kit Installation Notes...
- Page 6 AP60-MNT: Installation Notes Vertical Post Mount Strap Slots 5 Mounting the Cradle to a Vertical Post IGURE To mount the AP to a vertical post, thread two metal or plastic mounting straps (not included) around the post and through the large slots on the cradle. The straps should be flat and no wider than 1.5 cm (5/8 inches).
- Page 7 7 Removing the LED label IGURE The label conceals a mounting hole required in a later step. (You will remove and discard this label and replace it with the extra label shipped with this kit.) The AP60/61 Mounting Kit Installation Notes...
- Page 8 AP60-MNT: Installation Notes 2. Place the AP into the mounting cradle. 8 Placing the AP60/61 into the Cradle IGURE Fit the keyhole-shaped slots on the rear of the AP chassis over the cradle mounting pin and tab. Slide the AP chassis downward so that the AP slot captures the tab.
- Page 9 6. Orient the antennas. For best performance, orient the antennas vertically. 7. Resume standard installation. Once mounting is complete, connect the required cables and complete the installation as described in the AP60/61 Wireless Access Point Installation Guide. The AP60/61 Mounting Kit Installation Notes...
- Page 10 AP60-MNT: Installation Notes Notes Part 0500037-03 May 2005...
- Page 11 The AP60/61 Mounting Kit Installation Notes...
- Page 12 AP60-MNT: Installation Notes Part 0500037-03 May 2005...