Programming Features; Other Remote Start Features; Low Battery Automatic Starting; Turbo Timer Feature - Omega RS-310-EDP Operation Manual

Programming Features

Step 1 Turn the vehicles's ignition on.
Step 2
Turn the ignition off.
Step 3
Within 5 seconds, Press & Release the Valet
5 times for User Programming
OR
10 times for Installer Programming
• The horn will chirp then sound briefly (and the Status Light will turn on) to
confirm that the system is entering Programing Mode.
• In the case of accessing the Installer Mode, the horn chirps then briefly sounds
at the fifth valet switch press, and then again at the tenth valet switch press.
• In either Programming Mode, if 10 seconds of no programming activity
occurs, the system will exit Programming Mode.
Access a Feature:
Step 4 Within 10 seconds, Press & Release the Valet Switch the same num-
ber of times as the desired feature's number.
• The horn will chirp, the parking light output will flash, (and the Status
Indicator Light will flash) as many times as the Valet Switch was pressed to
indicate the feature number accessed.
Change the Feature:
Step 5 After accessing the desired feature, within 10 seconds Press &
Release the appropriate controller or transmitter button.
• Pressing the "lock" button typically turns the feature on; or sets the
feature's first option. The horn will chirp once and the parking lights will
flash once when this button is pressed.
• Pressing the "unlock" button also typically turns the feature off; or,
sets the feature's second option. The horn will chirp twice and the lights will
flash twice.
• Many features have third, and even fourth setting options. Pressing the "trunk"
and "start" buttons select these options. Confirmation chirps when these
buttons are pressed are three and four chirps respectively.
To Access and Change further Features:
Step 6
If there are more features to be programmed, within 10 seconds of
the previous action Press & Release the Valet Switch the same
number of times as the next desired feature's number.
• Again the horn will chirp, the parking lights, (and the Status Indicator Light)
will flash as many times as the Valet Switch was pressed to indicate the new
feature number which is now accessed. Then use the controller or transmitter
as described in Step 5 to change the newly accessed feature as desired.
Switchch either:
Page - 12

Other Remote Start Features

Low Battery Automatic Starting Feature
Setting this feature to operate has the RS-310-EDP automatically start
the engine should the vehicle battery voltage drop to 10.5 volts. This fea-
ture is very useful if the vehicle is to parked unattended for a long period of
time, such as extended parking at the airport while away. Low Battery
automatic starting must be activated for each occasion in which you desire
it to operate, as follows:
• Turn the ignition switch "on", then "off" (engine not running), and within
7 seconds press the brake pedal twice. The system will chirp 6 times.
Then, within 5 seconds, exit the vehicle and press the transmitter's
"lock" button to lock the vehicle.
The feature is now turned on, and until the system is disarmed or the igni-
tion turned "on", if the system detects the vehicle battery voltage dropping
to 10.5 volts, it will automatically start the engine.

Turbo Timer Feature

It is typically recommended that vehicles equipped with turbocharged
engines allow the engine to idle for a few minutes before turning it off.
When this Installer Programmable Feature is programmed on, the RS-
310-EDP will automatically keep the engine running as follows:
• With the engine running, hold the brake pedal and engage the parking
brake. When the brake pedal is released, the RS-310-EDP will keep the
engine running for the selected time, and then automatically turn it off.
The turbo timer feature must be programmed by the installer, and turn-
ing it on offers three run time choices- 1, 2, or 3 minutes. The system may
be locked while the engine is running. Turbo Timer can be prevented from
engaging, or "bypassed" if desired, by turning the engine off first and then
engaging the parking brake, or if it's already engaged simply step on the
brake pedal to turn the running engine off.

The Status Light

The Status Light helps to visually confirms the status of the system and
provides a high level of visual deterrence. The Status Light is located in the
window mount receiver unit.
Normal System Status
1) Off = The system is unlocked and the remote starter system is off, but
in standby mode.
2) On Constant = The system is in the Valet Mode, with the remote starter
system disabled.
Page - 9