Download  Print this page

Advertisement

Advertisement

Table of Contents

   Summary of Contents for Mitsubishi Electric NM-C110

  • Page 2 This unit complies with the requirements of the EC Directive 2004/108/EC, “EMC Directive”. The requirements for the susceptibility according to EN 55024 and the requirements for interference according to EN 55022 are observed for the operation on residential areas, business, light industrial premises and in small scale enterprises, inside as well as outside of the building.
  • Page 3 2002/96/EC Article 10 Information for users and Annex IV, and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II. Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused.
  • Page 4: Important Safeguards

    IMPORTANT SAFEGUARDS READ INSTRUCTIONS -- All the safety and operating instructions should be read before the appliance is operated. RETAIN INSTRUCTIONS -- The safety and operating instructions should be retained for future reference. CLEANING -- Unplug video monitor or equipment from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
  • Page 5 15. SERVICING -- Do not attempt to service video monitor or equipment yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 16. DAMAGE REQUIRING SERVICE -- Unplug video monitor or equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power-supply cord or the plug has been damaged.
  • Page 6: Table Of Contents

    TABLE OF CONTENTS 1. Production Introduction ………………………………………… 1 1.1 Components ……………………………………………………………………………………… 1 1.2 NETWORK CAMERA'S External View and Port Description ……………………………… 1 1.2.1 Front View …………………………………………………………………………………… 1 1.2.2 Back View …………………………………………………………………………………… 2 1.2.3 Side View …………………………………………………………………………………… 2 1.2.4 Top View …………………………………………………………………………………… 2 2.
  • Page 7: Production Introduction

    1. Product Introduction Unlike an analog camera, the NETWORK CAMERA enables users to easily see a real-time monitoring screen on Internet regardless of distance and locations, requiring no additional equipment. By using its dedicated program, many users are able to have an access to the NETWORK CAMERA at once or a single user can monitor various NETWORK CAMERAS at the same time.
  • Page 8: Back View

    1.2.2 Back View DC 12V : Reset Button 1.2.3 Side View 1.2.4 Top View - 2 -...
  • Page 9: Network Camera Installation

    2. Network Camera Installation 2.1 Installation Order Before operating this Network Camera, make sure to connect a network cable to power. Users can add an alarm cable or an audio cable there depending on what operation methods they choose. As far as a camera-fixing stand is concerned, consult with an installer about its installation locations.
  • Page 10: Audio Connection

    2.3 Audio Connection The NETWORK CAMERA enables users to send and receive a voice through the input/output module. Use it after connecting the port to the microphone and speaker, which have an amplifier function. External Speaker External Microphone 2.4 Alarm Connection Users can control the alarm systems like a siren, an Alarm Input 1 alarm and a warning light through two alarm inputs.
  • Page 11: Operation By Web Browser

    3. Operation by Web Browser 3.1 Connecting the Network Camera by Web Browser ●Execute the Web Browser on the PC. ●Enter the camera address on the address window of the Web Brower and execute it. http://192.168.0.2/ (If the camera has no IP address or its IP address is wrong, users will fail to connect the camera.
  • Page 12: Network Camera Setting

    3.3 NETWORK CAMERA Setting Camera setting is divided into video, audio, alarm, and system settings. And the detailed screen will be provided for each setting. 3.3.1 Video Setting The video setting is classified into Basic, MPEG-4, and Still Images. The Basic menu includes a setting menu for real-time monitoring.
  • Page 13 MPEG4 Video Stream Frame rate Upon the real-time play, users should select a frame refresh rate per second. If the rate is high, the image will become smooth. On the other hand, if the rate is low, the image will not be natural but it can reduce a network load. Bit-rate control Variable bit rate (VBR): It refers to the type of using a variable bit rate (VBR).
  • Page 14 AE & AWB Setting For more detailed settings, users can set the white balance and automatic exposure control. It is possible to designate the basic value according to the types of light or set it to a full automation mode. White Balance Control White Balance Mode When it comes to the White Balance Mode, users should select an illumination mode...
  • Page 15: Audio Setting

    3.3.2 Audio Setting Basic Setting Users can use a microphone and speaker by using the audio function. Audio Setting Compression type Users can increase a transmission rate or enhance a tone quality by selecting an audio compression mode. The PCM 16-bit implements the best tone quality, while the PCM 8-bit corresponds to that of radio sound.
  • Page 16: Alarm Setting

    3.3.3 Alarm Setting Alarm In Setting This function enables users to conduct the alarm input/output setting and event setting. Motion Detection Setting Motion information is processed by splitting the screen into 64 areas. Each area can be selected by clicking with the mouse, and green point shown in the selected area. The area which uses the motion information as an event is shown green point, while the area which does not use the information is indicated empty.
  • Page 17 Alarm IN Port 1 Setting Type Select the operation mode of the Alarm Input 1. Select either ‘N.O.(Normal Close)’ or ‘N.C.(Normal Open)’ Alarm dwelling time [0~180] Designate a running time for alarm occurrence. Select one out of 0 to 180 seconds. Alarm IN Port 2 Setting Type Select the operation mode of the Alarm Input 2.
  • Page 18 Alarm Out Setting Upon the alarm occurrence, this function enables users to receive a mailing or ftp service to the mobile phones or mail address designated by users. SMPT(eMail) Setting Sender : Enter an eMail address to send a mail. Receiver list: Enter up to 10 eMail addresses to receive a mail.
  • Page 19 -JPEG Settings Sets up the creation condition, screen size, color and name of JPEG file to be sent to FTP. Pre event: Creates the JPEG file of chapter 1~5 for 1~2 seconds before the event is generated. Post event: Creates the JPEG file of chapter 1~15 for 1~2 seconds after the event is generated.
  • Page 20: System Setting

    3.3.4 System Setting Users Setting This NETWORK CAMERA's Authority Policy 1. Anonymous User Access Permit Mode This mode enables any anonymous users to have an access to the NETWORK CAMERA to monitor and set it. 2. Anonymous User Access Denial Mode Upon selecting this mode, the NETWORK CAMERA operates in two authority groups.
  • Page 21 User List Setting Show a registered user account. -Add User Enter a user name and password to be added, and register them by pressing the “Add” button. -Modify User Information After selecting a user to be corrected and changing its name and password, press the ‘modify’...
  • Page 22 Date & Time Setting Date & Time Current Time: Indicate a current time. Date: Indicate a current day, month, and year. Time: Indicate a current day, month, and year. New Time Time Zone: Select a time zone to be used. Automatically adjust for daylight saving time changes: Check it if users are to apply the Summer Time.
  • Page 23 Network Setting Setting in regard to network can be executed. Settings for IP, DNS, Host Name, Port, and Network traffic can be established, along with setting for DDNS and RTP. Basic Setting Basic settings for IP, DNS, Host Name, and Port are possible, and possibly works as a adjustment role in reducing the overload of network bandwidth in use, by applying Network traffic capability.
  • Page 24 Services HTTP port: Enter a port to receive a service through the HTTP. Default Port Number is ‘80’. RTSP port: Enter a port to receive a service through the RTSP. Default Port Number is ‘7070’. Network traffic - Maximum bandwidth Set a limitation on user network resources by designating the maximum bandwidth.
  • Page 25 RTP Setting Have a setting for sending and receiving an audio or video on a real-time basis. Stream RTP after Network Camera start-up Enter a destination IP and Port to send stream automatically through the RTP while the Network Camera has booting. Send to DHCP server IP: Send stream to the DHCP server.
  • Page 26 RTSP/RTP settings Perform a multicast setting to send a video and audio to multiple users. (Up to 10 users) RTP destination IP Disable Multicast: Do no use the multicast. Enable Multicast: Use the multicast. Multicast destination IP: Enter an IP between 224.0.0.0 and 239.255.255.255. Although it is empty, an IP will be entered automatically.
  • Page 27 Maintenance Maintain Server < Restart > Restart the NETWORK CAMERA. < Userset > Initialize a user setting value of audio/video, alarm, etc. < Restore > Restore all the values except a network-related setting to a basic value. < Default > Restore all the setting values to a basic value. Upgrade Server Carry out the upgrade by importing an upgrade file and pressing the ‘Upgrade’...
  • Page 28 Program Support Information Troubleshooting When problems occur during operation, please consult with an installer. Server Report If its support is requested, please attach a server report. Log & Report Users can check the system log and server report. ■ Logs Reports Users can check the log Users can check a...
  • Page 29: Help

    Program Information The following website will provide the support information for the NETWORK CAMERA system information and operation. 3.4 Help The Help information window will be provided as a popup window so that users can open and read it without a need for log-in. It will offer a description on setting and Help page by which users can manipulate the Network Camera without a reference to the manual.
  • Page 30: Appendix

    4. Appendix 4.1 Troubleshooting If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information.
  • Page 31: Product Specifications

    4.3 Product Specifications Video Resolution 640 X 480 / 320 X 240 / 160 X 120 Frame rate Max 30 fps @ 640 X 480 resolution 1/4” Progressive scan R,G,B CCD sensor Video compression MPEG4 SP and ASP Compression option Variable bit rate / Constant bit rate Lens mount C mount, CS mount...
  • Page 32 Fax: +39 (039)-605 3214 GERMANY Mitsubishi Electric Europe B.V. The Netherlands German Branch Office Mitsubishi Electric Benelux Electric Visual Systems A Division of Mitsubishi Electric Europe Gothaer Str. 8 40880 Ratingen B.V. Germany Niiverheidsweg 23A, 3611 RP Mijdresht Netherlands Telephone: +49 (2102)-486 9250...

Comments to this Manuals

Symbols: 0
Latest comments: