Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Roland V-PAD PD-105X
Summary of Contents for Roland V-PAD PD-105X
-
Page 2: Using The Unit Safely
Refer all servicing following all the rules essential for the safe operation to your retailer, the nearest Roland Service Center, or of the unit. an authorized Roland distributor, as listed on the ........................ -
Page 3: Important Notes
Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2009 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. -
Page 4: Main Features
Main Features • Snare/tom pad with mesh head allowing for excellent feel, dynamics and low level acoustics sound. • Rim shots and playing with brushes is possible. • The pad can mount on a V-Drums drum stand and/or commercially available tom stands (vertical rod type or horizontal pipe type p. 5) (PD-125X/105X only). -
Page 5: Mounting The Pads
Mounting the Pads Mounting the PD-125XS Mounting the PD-125X or 105X on (Dedicated Snare Pad) a Tom Stand The PD-125XS (dedicated snare pad) has no mounting The PD-125X/105X can be attached to a stand that has either bracket so can only be used with a snare stand. a vertical rod or a horizontal pipe. -
Page 6: Sound Module
Connecting to the Percussion Sound Module Recommended parameter settings Use the included stereo cables to connect pads to your percussion sound module (sold separately). Below please find recommended trigger parameter settings Connect the L-shaped end of the cable to the pad’s OUTPUT when using the PD-125XS/125X/105X with various sound jack. -
Page 7: Adjusting The Head Tension
• Adjust the tuning bolts so that they are not loose. For replacement heads or to have the hoop rubber replaced, fig.19-e.eps.80 please contact your dealer or a Roland service center. Replacing the Head Applying excessive force to the sensor located under the head can damage it and/or interfere with accurate triggering. - Page 8 Replacing the Shell Covering Pull the fastening clip upward and out, and remove the covering. • Applying excessive force to the sensor located under the head can damage it and/or interfere with Fastening Clip accurate triggering. • Be careful not to hurt your fingers on the corners or Covering points of the metal parts.
- Page 9 Install the frame in the shell. The frame’s output jack will be pointing in the same direction as the bracket. Output jack Frame Protrusion Shell Groove Bracket Match up the protrusion on the frame with the groove on the shell. Attach the hoop and head, and tighten the tuning bolts.
-
Page 10: Playing Methods
Playing Methods Head shots Change the Nuance of the Rim Shot fig.Head.e (Only with the TD-20X/TDW-20/TD-20/ Only playing the head TD-12) and with certain snare sounds, the playing position will change the With certain snare and tom sounds, slight changes in the way Head sound’s nuance. -
Page 11: Specifications
Specifications PD-125XS/PD-125X/PD-105X: V-Pad PD-125XS PD-125X PD-105X Pad size 12 inch 12 inch 10 inch Trigger 2 (Head, Rim) Bracket – – – 358 (W) x 322 (D) x 117 (H) mm 358 (W) x 368 (D) x 117 (H) mm 307 (W) x 317 (D) x 117 (H) mm Dimensions 14-1/8 (W) x 12-11/16 (D) x 4-5/8 (H) inches... - Page 12 For EU Countries For China For C.A. US ( Proposition 65 ) WARNING This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
- Page 13 Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. AFRICA PHILIPPINES CURACAO URUGUAY NORWAY JORDAN G.A. Yupangco & Co. Inc. Zeelandia Music Center Inc. Todo Musica S.A.