Table of Contents
Advertisement
How to use the Unicouple
Before
operating
your
dishwasher
the first
time...
Attach
the Faucet
Adapter.
The
special
faucet
adapter
supplied
with your dishwasher
must
be
assembled
to the sink faucet
before
you can use your dishwasher.
The faucet adapter is designed to
fit standard spouts having internal
or external threads. You will find
the adapter and two washers in the
"Faucet
Adapter"
packet in your
dishwasher.
To install
faucet
adapter,
first
remove
the old aerator
or trim ring
on your
faucet
spout.
If faucet has external
threads:
g
Insert the thinner of the two
washers
into the faucet adapter and
attach it to the faucet spout.
If faucet has internal threads:
Insert both washers
into the faucet
adapter and attach it to the faucet
spout.
If the faucet adapter threads
do not match your faucet spout,
your local hardware or plumbing
supply store normally has
additional fittings to adapt your
faucet spout to the special faucet
adapter.
NOTE: A sink spray attachment
hose can burst (F"'itis installed on
the same sink with your dishwasher:
We suggest that you disconnect
the
sink spray attachment
if your sink
has one and plug the hole.
How to connect the
Unicouple
1. Pull Unicouplc
and its hoses
completely
out from
storage
compartment
located at rear of
dishwasher and attach it to the
faucet adapter,
2. Attach the Unicouplc
connector"
to thelhucet
adapter by depressing
collar at the top of the connector."
When Unicouple
is all tile way up
onto the adapter,
release
the col tar.
It will
then
snap
into position
to
lock the Unicouple in place.
The
Unicouple
s small
hose carries
water
from the faucct
to the
dishwasher. Its lar,,e hose carries
draill water to the sink. Be sure
Unicouple
is pointinglowardlhe
sink bowl drairi open sing and the
sink drain is open for water that
w i
II
drain from yourd i
shwushcr.
It
your
dishwasher
drains into a
disposer, operale
tile disposer unlil
it is completely
empty before
startinglhe
d i shwusher.
3. TUI'Ii hot wttlcr fullyonbcforc
starting
the dishwasher.
How to use the
Faucet-Flo
nozzle
_'-
f-;
PRESSURE
",_'_
RELEASE
:<:"
BUTTON
y }l
The Faucet-FIo
nozzle
is parl of tile
Unicouplc
connector."
()penile
lhe
IIOZZIe by
depressing
I.heplCSStllC
release
button
onthcfr(mtofthe
Unicouple
con|lector.
YOU will lilld
lheFaucel-Fh,
nozzlc
useful
for
sevclal
reasons. FOleX;.llllp]e
:
oltal lows you to flush cold
water-
outofthe
hot waterline
so that
you can better
regulate
your water
lempcralure.
*Ital
lows
you
10
test
the
temperature
of the water
before
start i ng your dishwasher.
How to disconnect
the
Unicouple
from faucet
adapter
1. Turn off lhc hot water.
2. Rclcase the water pressure by
depressingthe press ure release
bttttotl. This relieves water
pressure and protects
you, and the
room." from severe splashing.
3.Release
Unicouple from faucet
by depressing the collar at the top
of the Unicouple connector."
How to disconnect
your
dishwasher
l.
Remove
thepowercord
plug
from
ttle wall receptacle.
2. Disconnect
Unicouplefrom
luucet adapter.
NOTE: When motor" stops at the
end ol + the final rinse, the Unicouplc
can be disconnected
and returned to
storage.
How to drain
excess
water
from Unicouple
hoses
If the sink is 34" or higher
from
the floor+ the excess
water
in
gnicouple
hoses cannot be drained
directly
into
thesink.
Itwil[be
necessary
to drain excess
watet-
lromhoses
into a bowl or suitable
container
that is held outside and
lower than the sink.
12
Advertisement
Table of Contents
