Panasonic TH-65PF50U Operating Instructions Manual page 57

Item
Off:
Studio W/B On:
Note: Valid only when the "WARM" is set as "COLOR TEMP" in PICTURE menu.
Sharpens the contrast for a better view when a part of the image is too light to see.
Off:
Studio Gain On:
Note: This setting is valid only when the input signals are as follows:
Off
Off:
Auto: Power is transmitted to the slot power only when main power is on.
Slot power
On:
Note: In some cases, power is transmitted to the slot power when main power is on or in the standby state
Off
You can set the power-on delay time of the displays to reduce the power load, when you press
on the multiple displays that are set together, for example, on MULTI DISPLAY system.
Set each display's setting individually.
Off:
1 to 30 (sec.): Set the power-on delay time (second).
Power On Screen
Notes:
Delay
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power cord.
After you unplug and plug the power cord in while the unit is in standby mode and also the power is being
supplied to a terminal board, the unit will start supplying the power to the board with time delay according
to the setting.
The power indicator lights up red fi rst and it turns orange when the power starts being supplied to the board.
Off:
On:
The clock is displayed at the lower left of the screen when
Clock Display
Sets All Aspect mode (advanced aspect setting) or default aspect mode.
With each press of
Off:
On:
All Aspect
Aspect mode of each setting is as follows:
(Example: HD signal)
Off
On
Sets the operational mode of the automatic position adjustment in the POS./SIZE menu.
Manual: Automatic position adjustment starts when
Auto Setup
Auto:
Off:
Rotate On:
Note: During the image is rotated, the 3D images are displayed as 2D images.
Displays motion picture images at higher resolution.
On
Advanced Motion
Notes:
Resolution
• Please set to "Off" if images look unnatural.
• This function is disabled during 3D images.
Whether to show/hide No activity power off Precautions at the time of power ON is set.
Power On Message
On:
(No activity power
Off:
off)
Note: This setting is enabled only if "NO ACTIVITY POWER OFF" is "ENABLE" (see page 46).
Nullify all the settings adjusted.
Sets the color temperature for TV studio.
Disables "Studio Gain".
Enables "Studio Gain".
Component Video, RGB (analog), SDI, HDMI
Auto On
Power is not transmitted to the slot power.
Power is transmitted to the slot power when main power is on or in the standby state.
regardless of the slot power setting.
1 2 3.... 30
The display will be turned on at the same time as
After pressing , the display will be powered on with time delay depending on this setting.
Not display the clock.
Display the clock.
Note: When "DAY/TIME SETUP" is not set, the clock is not displayed even if
"Clock Display" is "On" (see page 36)
10:00
button, the aspect changes in the selected mode.
Default aspect mode
All Aspect mode
4:3→H-FILL→ZOOM→FULL→JUST
4:3 (1)→4:3 (2)→4:3 Full→Zoom1→Zoom2→Zoom3→16:9→14:9→Just1→Just2
adjustment is executed from the POS./SIZE menu.
Other than remote control or menu operation, automatic position adjustment starts:
When the display power is turned ON.
When the input signal is switched.
Does not rotate the image.
Rotates the image 180 degrees.
Off
The warning precautions are shown at the time of power ON.
The warning precautions are not shown at the time of power ON.
Options Adjustments
Adjustments
is pressed.
button is pressed.
is pressed on the remote control or automatic position
to turn
57