Troubleshooting; Front Key (Button) Lock Of The Unit; General Malfunction; How To Reset The Unit - Marantz SR5023 User Manual

Hide thumbs Also See for SR5023:
Table of Contents

Advertisement

TROUBLESHOOTING

In case of trouble, check the following before calling for service:
1.
Are the connections made properly ?
2.
Are you operating the unit properly following the user's guide ?
3.
Are the power amplifi ers and speaker working properly ?
If the unit does not operate properly, check items shown in the following table.
If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the
internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz
authorized dealer or the Marantz Service Center in your country.
SYMPTOM
SR5023 cannot be turned up.
The power plug is not connected.
No sound are output even when power
Mute is on.
is on.
The input cable is not connected
correctly.
The master volume control is turned all
the way down.
The function selector position is wrong.
No speaker output.
The headphones are connected to the
headphone jack.
Incorrect Audio for selected source.
Input cable connected incorrectly.
FM or AM reception fails.
Antenna connection is incomplete.
Noise is heard during AM reception.
Reception is affected by other electrical
fi elds.
Noise is heard during FM reception.
The radio waves from the broadcasting
station are weak.
Cannot get programmed station when
Preset data has been erased.
the PRESET button is pressed.
Control with the remote control unit fails.
Batteries are consumed.
Remote controller's function-key setting
is wrong.
The distance between this unit and the
remote commander is too far.
Something is blocking unit and the
remote commander.
The main unit and remote controller
are set to use different remote control
codes.
CAUSE
REMEDY
Connect the power plug to the outlet.
Cancel mute using the remote control
unit.
See the connection diagram and connect
the cables correctly.
Adjust the master volume.
Select correct position.
Disconnect the headphones. (Speakers
will not output sound when headphones
are connected.)
Connect the cable correctly by referring
to the connection diagram.
Correctly connect the indoor FM and
AM antennas to FM and AM antenna
outlets.
Try changing location where the AM
indoor antenna is set up.
Install an FM outdoor antenna.
Disconnecting power plug for long
periods of time will erase preset data.
If that happens, input the preset data
again.
Replace all the batteries with new ones.
Select different position from which
equipment will be controlled.
Move closer to this unit.
Remove offending object.
Set the main unit and remote controller
to use the same remote control code.
S.DIRECT
F/P
T.MODE
MUTE
DISP
AUTO
TUNED
ST
SLEEP
DIRECT

FRONT KEY (BUTTON) LOCK OF THE UNIT

If the F/P and T.MODE buttons on the front panel are
both pressed at the same time for three seconds or
more, all the buttons on the front panel, (excluding
the POWER ON/OFF button), as well as the INPUT
SELECTOR knob and VOLUME knob, will become
locked. "F-KEY LOCK!" will appear in the display.
Release the lock by pressing the same two keys
again at the same time for three seconds or more.
"F-KEY UNLOCK" will appear in the display, and the
keys will unlock.

GENERAL MALFUNCTION

If the equipment malfunctions, this may be because
an electrostatic discharge or AC line interference has
corrupted the information in the equipment memory
circuits. Therefore:
-
disconnect the plug from the AC line supply
-
after waiting at least three minutes, reconnect
the plug to the AC line supply
-
re-attempt to operate the equipment
Memory backup
• In case a power outage occurs or the power
cord is accidentally unplugged, this unit is
equipped with a backup function to prevent
memory data such as the preset memory
from being erased.
ENGLISH

HOW TO RESET THE UNIT

Should the operation or display seem to be abnormal,
reset the unit with the following procedure.
The SR5023 is turned on, press and hold the MUTE
and S.DIRECT buttons simultaneously for 3 seconds
or more.
Remember that the procedure will reset the settings
of the function selector, TUNER PRESET etc., to
their initial settings.
17
17

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents