Scag Power Equipment STC Operator's Manual page 45

Section 8
Ref. Part
No. No.
1 482624
2 04020-28
3 481766
4 04050-10
5 482429
6 43487
7 423463
8 04009-02
9 48100-14
10 482707
11 461587
12 422346
13 04014-03
14 422381
15 04003-04
16 422380
17 481598
18 04021-05
19 04040-09
20 04019-04
21 04001-32
22 43611
23 04061-07
24 04019-04
25 04001-20
26 04019-04
27 04021-09
28 48540
29 48114-04
30 04021-09
31 04041-07
32 04004-45
33 481547
34 04020-09
35 43612
36 04001-155
37 481765
38 04001-77
39 43572
40 04021-02
41 43557
42 04020-27
43 04021-10
44 45904
45905
04041-14
04050-08
45 04062-04
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
CUTTER DECK CONTROLS
Description
Rod, Deck Lift Linkage
Nut, Jam 1/2-20 LH Thread
Rod End, 1/2-20 Female Thread
Retaining Ring, 1/2" External "E"
Slide, Deck Height Adjust
Pin, Deck Lift
Bracket, Cutting Height Adjustment
Bolt, Shoulder 1/2-3/4"
Bushing .502 ID
Grip, Deck Latch Lever
Lever, Deck Latch (Includes 9 &10)
Slide, Cutting Height
Screw, Cap 5/16-18 x 3" FHHS
Guide, Short
Bolt, Carriage 5/16-18 x 1"
Guide, Long
Spring, Helper
Nut, 3/8-16 Center Lock
Flatwasher, 5/8-.656 x 1.312 x .095
Nut, 3/8-16 Serr. Flange
Bolt, Hex Head 3/8-16 x 1-1/4"
Swivel Joint LH
Cotter Pin, 3/16 x 1"
Nut, Serr. Flange 3/8-16
Bolt, Hex Head 3/8-16 x 1-1/2"
Nut, Serr. Flange 3/8-16
Nut, Elastic Stop 3/8-16
Chain
Grease Fitting, 1/4-28 Self Tap
Nut, Elastic Stop 3/8-16
Flatwasher, 3/8-.391 x .938 x .105
Stud, 1/2-13 x 20"
Lanyard Pin
Nut, 5/8-11 UNC
Swivel Joint RH
Bolt, Hex Head 1/2-13 x 5"
Rod End, 1/2-20 Female RH Thread
Bolt, Hex Head 3/8-16 x 3-1/2"
Spacer
Lock Nut, 1/4-20
Spacer
Nut, 1/2-20 UNF-2B
Nut, Elastic Stop 5/16-18
Lift Bellcrank Weldment, LH Rear
Lift Bellcrank Weldment, RH Rear
Flatwasher, 1.0-1.062 x 1.5 x .048
Retaining Ring, 1" ext.
Hair Pin Cotter, .177 x 3-1/4"
41