Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GoPro 3D Hero SyStem
Summary of Contents for GoPro 3D Hero SyStem
- Page 1 3D Hero SyStem ® User ManUal + Warranty Info...
-
Page 2: Firmware Update
YouTube that support 3D videos, or on your 3D TV at home using active or passive shutter glasses depending on your 3D TV. To download and install your free copy of GoPro CineForm Studio, visit gopro.com/3D. - Page 3 3D Hero systeM featUres 1. Master Shutter Button 3. Left Camera Power Button 5. Mounting Fingers 8. Requires Two 1080p Controls Both Cameras HD HERO Cameras 4. Center Mount Adapter 6. 3D HERO Sync Cable (not included) 2. Right Camera Power Button 7.
- Page 4 Note: The 3D HERO System requires two 1080p HD HERO cameras. Each camera requires a fully charged battery and SD card with sufficient memory for recording (GoPro recommends Class 4 or faster SD cards). Each camera’s settings (e.g.: resolution, exposure, record mode, video format (PAL & NTSC)) must match for 3D synchronization to work.
- Page 5 To combine cameras in 3D HERO System waterproof housing: 5. Make sure the 3D Sync Cable is fully inserted and is flush against the back of the cameras. 1. Open back door to the 3D housing. Close waterhousing. 2. Insert “right” camera right side up into housing. If settings are changed and you wish to return each camera to its default 3D setting, simply unplug the sync cable and 3.
- Page 6 UsInG tHe 3D Hero systeM Additional Notes: • Blinking front LCD screen and red LED record lights may ImPortANt: to capture 3D video and photos, both cameras or may not blink in sync. This is OK and has no effect on must be set to identical resolution, record mode and frame whether or not each camera is in sync with the other.
-
Page 7: Mounting Configurations
MoUntInG ConfIGUratIons ImPortANt: It is recommended to use dual quick-release buckles for mounting the 3D Hero System whenever possible for maximum stability. Using a single center mounted quick-release buckle is only recommended for chest, helmet, suction cup, and other body worn applications where high vibration or impact are less likely. Use of a single center quick-release buckle in high vibration or high impact scenarios can result in less stable video compared to using two quick-release buckles. - Page 8 CUrVeD AND FLAt SUrFACe moUNtING FroNt HeLmet AND CHeSt moUNtING Front Helmet mount: Attach the Front Helmet Mount to the center fingers with The extension arms and quick-release buckles can be the center mount adapter and long thumb screw. used in a number of different orientations depending on what type of surface you are attaching the 3D HERO System Chest mount: to.
- Page 9 • To prevent fogging when using the waterproof back cause eye strain when viewing during playback. door, use GoPro’s anti-fog inserts with your 3D HERO System housing. • For best 3D results, the right camera must be in UP and the left camera must be in UPd recording modes.
- Page 10 To convert 2D video and photo files into 3D files, you will need cable, turn on the camera, and locate the Removable Disk to use GoPro CineForm Studio software. GoPro CineForm (SD Card) icon. Once the icon is located: Studio and associated instructions are available as a FREE download from: gopro.com/3D.
-
Page 11: Important Safety + Handling Information
Improper alignment of your 3D images or misuse of the to dry the 3D sync cable with an external heat source, such as GoPro CineForm Studio software while viewing with 3D a microwave oven or hair dryer. Damage to the 3D sync cable glasses may cause eye strain or headaches. -
Page 12: Warranty
Damage resulting from use, accident, or normal wear and tear is not covered by this or any warranty. GoPro assumes no liability for any accident, injury, death, loss, or other claim related to or resulting from the use of this product. In no event shall GoPro be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its parts.
Need help?
Do you have a question about the 3D Hero SyStem and is the answer not in the manual?
Questions and answers