Genelec 1029A Datasheet page 4

1029A Data Sheet
Figure 6: The curve above shows the effect of the 'treble tilt', 'bass tilt'
and 'bass roll-off' controls on the free field response.
SYSTEM SPECIFICATIONS
Lower cut-off frequency, –3 dB:
Upper cut-off frequency, –3 dB:
Free field frequency response of system:
70 Hz –18 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on axis
in half space, averaged from 100 Hz to 3 kHz:
@ 1m
@ 0.5m
Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by driver unit
protection circuit): @ 1m
@ 0.5m
Maximum peak acoustic output per pair on top of
console, @ 1 m from the engineer with music material:
Self generated noise level in free field @ 1m on axis:
< 10 dB (A-weighted)
Harmonic distortion at 85 dB SPL @ 1m on axis:
Freq: 75...150 Hz
> 150 Hz
Drivers: Bass 130 mm (5") cone
3
Treble 19 mm ( / ") metal dome
4
Both drivers are
magnetically shielded
Weight: 5.7 kg (12.5 lb)
Dimensions: Height 247 mm
Width 151 mm
Depth 191 mm
Genelec Document BBA29001a. Copyright Genelec Oy 1.2003. All data subject to change without prior notice
CROSSOVER SECTION
< 68 Hz Inputs: Input 1: XLR female, balanced 10 kOhm
Input 2:
> 20 kHz
Input level for 100 dB SPL output at 1 m:
-6 dBu at volume control max
Volume control range:
>70 dB relative to max output
> 100 dB SPL Subsonic filter below 68 Hz :
> 106 dB SPL
7050A/1091A Subwoofer output (input 2) at 100db SPL:
–23 dBu into 33kOhm load
> 98 dB SPL Ultrasonic filter above 25 kHz:
> 104 dB SPL
Crossover frequency, Bass/Treble:
Crossover acoustical slopes:
> 110 dB 24–32 dB/octave
Treble tilt control operating range:
0 to –2 dB @ 15 kHz
Bass roll-off control operating in a –6 dB step @ 85 Hz
< 3% (to be used in conjunction with 7050A or 1091A
< 1% subwoofer)
Bass tilt control operating range in –2 dB steps:
0 to –6 dB @ 150 Hz
The 'CAL' position is with all tone controls set to 'off' and
the input sensitivity control to maximum (fully
clockwise).
(9 3 / ")
4
15
(5 / ")
16
1
(7 / ")
2
International enquiries:
Genelec Oy, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83 881
Fax +358 17 812 267
Email genelec@genelec.com
Figure 7: The curve group shows the horizontal directivity characteristics
of the 1029A in its vertical configuration measured at 1m. The lower
curve shows the systems power response.
1 / " Jack socket, balanced 10 kOhm
4
18 dB/octave
12 dB/octave
3.3 kHz
In the U.S. please contact
Genelec Inc., 7 Tech Circle
Natick, MA 01760
Phone +1 508 652 0900
Fax +1 508 652 0909
Email genelec.usa@genelec.com
AMPLIFIER SECTION
Bass amplifier output power with an 8 Ohm load:
Treble amplifier output power with an 8 Ohm load: 40 W
Long term output power is limited by driver unit
protection circuitry.
Amplifier system distortion at nominal output:
THD
SMPTE-IM
CCIF-IM
DIM 100
Signal to Noise ratio, referred to full output:
Bass
Treble
Mains voltage:
100/200, 115/230 or 230 V
according to region
Voltage operating range:
Power consumption: Idle
Full output
www.genelec.com
40 W
< 0.08%
< 0.08%
< 0.08%
< 0.08%
> 90 dB
> 90 dB
±10%
9 VA
80 VA