Power Cord Care; To Assemble - Fellowes PDS-1 Use And Care Manual

PRODUCT USAGE GUIDE
Sheet capacity*:
Shred type:
Shred size:
Entry width:
Operation time:
*Sheet capacity measured with 20 lb. (70 g / m
voltage. Different paper weights, humidity, and electrical currents will affect capacity.
PARTS OF THE SHREDDER
A
D
B
A. Paper entry D. Power switch
B. Basket E. Shredder head
C. Auto-start sensor
2
PDS-1
4 sheets folded
Confetti
5/32" x 7/8" (4 x 22 mm)
4-1/2" (114 mm)
Short time operation 4 min.
), 8-1/2" x 11" paper with the shredder operating at rated
2
ASSEMBLY
E
C
Safety
Tab
NOTE: This shredder will operate only when used with the
supplied basket. The supplied basket has a built-in safety
feature which prevents the shredder from operating if used with
any other basket or if improperly assembled.
To assemble shredder
This shredder contains sharp edges on the underside of the
shredder head. Use caution when positioning the shredder
head onto the basket..
1 . Remove protective corrugated cover on back of shredder
and caution label on top of shredder.
2 . Position shredder head over basket as shown in Figure 1.
3 . Align slot on front of shredder head with the tab on the
inside front or back of the basket.
4 . Lower shredder head onto basket (while maintaining safety
tab/slot alignment).
IMPORTANT SAFEGUARDS
• NEVER insert hands or fingers into paper entry
as serious personal injury may result.
• THIS MACHINE IS NOT A TOY. Keep children and pets
away from shredder AT ALL TIMES as serious
injury may result. Always unplug shredder when
not in use.
• Keep loose objects (jewelry, ties, long hair) away from
shredder. These items and others like
them may cause serious injury if they
accidentally fall into the paper entry.
• Confetti cut shredders contain sharp edges on the
underside of the machine. Use caution when positioning
the shredder head onto the basket.
• 4 folded sheets per pass to avoid jams.
• Do not shred plastic, continuous forms, adhesive labels,
transparencies, glossy paper, newsprint, or cardboard.
• This shredder will shred paper, staples and credit cards.
Do not attempt to shred paper clips or other hard materials
(except those noted above).
• Do not place shredder near or over a heat source or water.
• Always turn off and unplug unit before moving or cleaning
and when not in use.
• Do not insert aerosol cleaners into or around the shredder.
Some agents may combust, causing serious injury.
• Never use flammable synthetic oil, petroleum-based or
aerosol lubricants to oil the cutting blades. Some agents
Figure 1
may combust, causing serious
injury.
• Do not use canned air on shredder.
• Do not use this product if it or the cord has been damaged
in any way.
• Do not open the cover for any reason. Doing so can
expose you to dangerous voltages and will void
your warranty.

Power Cord Care

• Place power cord in an easily accessible position, because
it is the main disconnect switch.
• Do not place machine where adults, children or animals
may walk on the cord.
• Do not rest anything on the power cord.
• If an extension cord is used, be sure that all products
plugged into the extension cord do not exceed the
extension cord ampere rating.
OPERATION
This product features an auto-start sensor. This sensor will turn
on the cutting blades whenever anything is inserted into the
paper entry (while the power switch is in the AUTO p o s i t i o n ) .
For the safety of pets and children, we recommend always
moving the power switch to OFF and unplugging
whenever the shredder is unattended or not in use.
1. Assemble shredder (see ASSEMBLY).
2. Remove any paper clips or other foreign objects (except
staples) from paper. If folding paper to fit paper entry,
adjust sheet capacity appropriately.
Do not attempt to shred paper clips or other hard materials
(except staples) with this machine. Extensive use of paper clips
or other hard materials will result in damage to the cutting
system and will void the manufacturer's warranty.
3. Be sure power switch is in OFF position. Plug shredder
into proper power supply outlet.
4. Move power switch to AUTO position. When the unit is
turned on and in standby mode, the shredder is ready to
be fed paper through the paper entry.
NEVER insert hands or fingers into paper entry as
serious personal injury may result.
Do not exceed recommended sheet capacity. See P r o d u c t
Usage Guide (page 2).
5. Slide paper straight into paper entry until the shredder
automatically begins shredding. (if paper is wider than
paper entry, fold paper in half before shredding)
The shredder automatically stops a few seconds after
shredding is complete.
If the shredder jams or shuts off before the maximum
shredding time, see Clearing a Jam for more information.
6. Move power switch to off position when shredding is
complete.
7. Unplug power cord from outlet whenever shredder is
unattended or not in use.
8. Check basket to see if it is full. If full, remove shredder
head and empty basket contents. Replace shredder head
onto basket.
3