Summary of Contents for Fantasea EyeGrabber MPK Series
Page 1
Fantasea EyeGrabber Sony MPK Series (Cat. No. 4056) Instruction Manual The EyeGrabber Sony MPK Series allows for secure storage of Fantasea accessory lenses and filters when not installed on the housing. Compatible with the Following Lens Accessories: BigEye Lens MPK Series (Cat. No. 5141) EyeDaptor MPK Series‐F67 ‐ with any lens accessory mounted on the (Cat. No. 4711) adaptor SharpEye Lens M67 ‐ ONLY when mounted on top of the EyeDaptor (Cat. No. 5128) MPK Series‐F67 (Cat. No. 4711) Included in the Kit: T2 Connector ...
Page 2
longer screws are compatible with wider arms, such as Fantasea Flex arms, while shorter screws are compatible with narrower arms, such as Ball & Joint arms. Choose the proper set of screws for your system and leave the screws installed only inside the front part of the T2 Connector (image #1). Keep the other set of screws in storage for future use, in case you replace the arms used in your system. d. If assembling the EyeGrabber on a Flex arm, gently rotate the links of the arm so that two sequential holes positioned on the upper half of the arm are aligned in a way that enables inserting screws inside (image #2). If assembling the EyeGrabber on a Ball & Joint arm, simply choose two slots on the upper half of the arm which the EyeGrabber will be assembled through. Image #2 Image #1 e. Hold the front part of the T2 connector with the two screws installed inside in front of the arm, so that the screws are aligned with the two holes or slots in the arm. Insert the screws through the holes or slots of the arm (image #3). Any resistance encountered might be due to improper alignment of the holes on the Flex arm. In such a case, please repeat step 1c. f. Hold the rear part of the T2 Connector on the other side of the arm, so the narrow side of it is facing the arm and aligned with the screws (the flared side with conical holes should be facing outward). Insert the screws into this part of the connector as well and tighten them till both sides of the T2 Connector are stable on the arm (image #4). If ...
Page 3
Image #3 Image #4 g. Hold the lens holder against one of the sides of the T2 Connector attached to the arm, so that the lens holder is facing out of the arm and the lens holder’s connector is aligned with the T2 Connector. Make sure that you attach the EyeGrabber on the T2 Connector that faces outward from the housing, so you will have more space to mount the lens on the EyeGrabber. Slide the lens holder on the T2 Connector and tighten the screw on the lens holder in order to fix its position (image #5). It is important to ensure that the lens holder connector and the T2 Connector are perfectly aligned prior to tightening the screw, or else the lens holder cannot be stabilized on the arm. h. Install the snap cord of the accessory lens on the arm. If you had the snap cord attached to the housing before, remove it and install it on the arm instead, so the accessory lens can be secured when mounted both on the housing lens port and the EyeGrabber. i. Mount the arm, with the EyeGrabber installed, on your housing tray or handle. ...
Page 4
2. Installing and Removing Lens Accessories from the EyeGrabber a. Installing and removing lens accessories from the EyeGrabber during the dive is the same as when installing and removing from the housing lens port (image #6). Hold the lens accessory in front of the EyeGrabber so that the “TOP” marking printed on the lens configuration is pointed opposite the EyeGrabber screw. This will make it easier to remove the lens accessory from the EyeGrabber later on. To install the accessory lens, push it against the EyeGrabber starting from the bottom and proceeding with the top. Make sure that the accessory lens is properly mounted on the EyeGrabber by gently trying to pull it out. If properly installed, the lens should not easily come off the EyeGrabber. b. It is recommended not to detach the secure line from the accessory lens during the dive, whether if mounted on the arm or on the housing lens port. c. In order to remove the accessory lens from the EyeGrabber, gently push it off, starting from the top and proceeding with the bottom. d. After the dive, detach the lens accessory from the EyeGrabber and rinse all components in fresh water. Dry with a soft clean cloth and store safely. Image #6 For further information, please contact us at www.fantasea.com/contact or visit our website www.fantasea. EyeGrabber Sony MPK Series Instruction Manual...