Advertisement
Stoppingthe Tiller and Eng ine
NOTE:If the belt is difficult to move, pull
1. To stop the wheels and tinesi release
on the engine start rope while pushing the
the Forward Clutch levers or the Reverse
belt with _our finger (engine drive pulley
Clutch Control (whichever is engaged):
will turnas start rope ispulled)
2. To stop the engine;move the Engine
6. Checkthat the beltis within theforward
Throttle Lever to STOPi
belt guide (E Figures 4-10 and 4-11)on
the
right,side of the unit and is within the
3, If the engine is equipped with a fuel
.......
•
forward _dler(Fi Rgure 4q t) Onthe left, .......
shutoff valvei close the valve as instructed
:
_,,
,..
side Be sure that the belt issituated in
in me Engine uwner s
lvlanual.
.......................................................................................
the center grooves (C and Di F!gure 4-1O)
oftheem
:upper) and transmission
engine;wait for all parts to stopmovingi
7i Reinstall the plastic belt cover and
let engine cool and disconnect spark
secure itwith the two nuts
plug
!i
8, Put Wheel Gear Lever in ENGAGE and
Failure tolollow these instructions could
reconnect spark plug wire before attemptiFigu
re4i11: Topviewofforward drivepulley
result in personalinjuryi
ingto start the engine.
SY stem (engineis at leftisideof view):
To Changefrom High to Low Speed:
2i Put Wheel Gear Lever in DISENGAGEi
CHANGING BELTRANGE SPEEDS
1.StoR the engine, allow itto cool; and
3 Remove the iwo nuis fiom the plastic
The iiller hastwo foiward belt iange
disconnecithe spaik plug wire.
b_li co,/ei on io; oi the tiansmission
Speedsfor the wheels and tines; L°w and
remove the belt coveri
"
i
'
TOrware
orlve Dell o U[OT l:ne l:rans mission
sets of grooves on the forward drive pulley
and thetransmission drive Rulley
NOTE: The High speed belt range is rec-
ommended fo rail tillingp urposes; The
Low speed belt range will operate thetines
and wheels at a slower forward speed;
which may be suitable in some co nd itions
(such as tilli ng i n ve_h ardg rou nd)
To Changefrom Low to High Speed:
1. Stop the enginei allow it to cool; and
disconnect the spark Rlug wire:
2. Move the Wheel Gear Lever into the
DISENGAG E positio n.
3. Removethe two nuts from the plastic
belt cover on top of the transmission and
removethe belt cover
4: From beneath the tiller;move the
Idler
i
D
(High)
pulley high speed groove (D, Figure 4-1O)
and into the low speed groove (B);
5: Pull upward on the belt to remove any
slack and slip the belt out of the engine
d rive puIley big h speedg roove (C, Figure
4-t0) and into the low speed groove (A)i
NOTE:If the belt is difficult to move; pull
on the engine start rope while pushing the
belt with your finger (engine driveRulley
will turn as start rope is pulled)i
6: Checkthat the belt iswithin the forward
belt guide (E, Figures 4-10 and 4-11) on
the right-side of the unit and is within the
forward idler (Fi Figure 4-11) on the left-
side: Be sure that the belt is situated in
the rear grooves (A and&Figure 4i10) of
the engine (uppeO and transmission
)pulleys;
forward drive belt out of the transmission
low speed g ioove (Bi Fig_ie4il O)and
transmissionpulleys (engineisat righttside
7 Reinsiall the plastic belt cover and
into the high speed groo#e (D)"'_'1
secure it with the two nuts
5: Pull upward on the beltto removeany
84 Put the Wheel Gear Lever in ENGAGE
Slack and
slip the beltout of the engine
and reconnect the spark plug wire before
drive pulley ow speedgroove (A, F gure
attempting !o Start the engine.
4-10) and into the high speed groove(C),
Advertisement
