Table of Contents
Advertisement
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 2.0
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and the receiver
•
Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system's manu-
facturer could void the user's authority to operate the equipment.
Preface
Preface
Advertisement
Table of Contents
Related Manuals for ECS H61H2-A
Summary of Contents for ECS H61H2-A
- Page 1 Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 2.0 Disclaimer The information in this document is subject to change without notice.
-
Page 2: Declaration Of Conformity
Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interfer- ence that may cause undesired operation. Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference- causing Equipment Regulations. -
Page 3: Table Of Contents
T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS Preface Chapter 1 Introducing the Motherboard Introduction..................1 Feature....................2 Specifications...................4 Motherboard Components............5 Chapter 2 7 7 7 7 7 Installing the Motherboard Safety Precautions................7 Choosing a Computer Case............7 Installing the Motherboard in a Case...........7... - Page 4 Security Menu ...............54 ..Exit Menu................55 Updating the BIOS..............57 Chapter 4 Using the Motherboard Software About the Software DVD-ROM/CD-ROM.........59 Auto-installing under Windows XP/Vista/7.......59 Running Setup................60 Manual Installation................62 Utility Software Reference............62 Chapter 5 ® Intel Matrix Storage Manager RAID Configurations Before creating a RAID set.............63 ®...
-
Page 5: Introducing The Motherboard
Chapter 1 Introducing the Motherboard Introduction Thank you for choosing H61H2-A motherboard. This motherboard is a high performance, enhanced-function motherboard designed to support the LGA1155 ® ® ® socket for latest Intel Core Family/Pentium /Celeron processors* to reach the optimum system performance for high-end business or personal desktop market. ®... -
Page 6: Feature
Feature Processor The motherboard uses an LGA1155 type of socket that carries the following features: ® • Supports 22nm & 32nm Intel Core micro-architecture • DMI 5.0GT/s • Supports “Hyper-Threading” technology CPU • One PCI Express x16 slot “Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate “logical”... -
Page 7: Bios Firmware
Onboard LAN (Optional) The onboard LAN provides the following features: • Supports PCI Express • Integrated 10/100/1000 transceiver • Wake-on-LAN and remote wake-up support • Supports PCI Express • Integrated 10/100 transceiver • Wake-on-LAN and remote wake-up support Expansion Options The motherboard comes with the following expansion options: •... -
Page 8: Specifications
Specifications • LGA1155 socket for latest Intel ® Core Family/Pentium ® Celeron ® processors • DMI 5.0GT/s • Supports “Hyper-Threading” technology CPU Chipset ® • Intel H61 Chipset Extra Chips ITE IT8893 PCI Bridge supports two PCI slots expansion • Memory •... -
Page 9: Motherboard Components
• Supports ACPI & DMI, Watch dog • Audio, LAN, can be disabled in BIOS • F7 hot key for boot up devices option • Supports eBLU/eDLU/eSF • Supports PgUp clear CMOS Hotkey (Has PS2 KB Model only) • Supports ACPI 3.0 revision •... - Page 10 Table of Motherboard Components LABEL COMPONENTS ® ® LGA1155 socket for latest Intel Core Family/Pentium 1. CPU Socket ® Celeron processors 2. CPU_FAN CPU cooling fan connector 3. DDR3_1~2 240-pin DDR3 SDRAM slots 4. ATX_POWER Standard 24-pin ATX power connector 5.
-
Page 11: Installing The Motherboard
Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a grounded device to avoid dam- age from static electricity • Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard •... -
Page 12: Checking Jumper Settings
Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. -
Page 13: Checking Jumper Settings
Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings Type Jumper Description Setting (default) 1-2: NORMAL 2-3: CLEAR CLR_CMOS 3-pin Clear CMOS Before clearing the CLR_CMOS CMOS, make sure to turn off the system. -
Page 14: Installing Hardware
Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resis- tors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. -
Page 15: Cpu Installation Procedure
CPU Installation Procedure The following illustration shows CPU installation components. A. Disengaging of the Load Lever · Hold the hook of lever and pull it to the left side to clear retention tab. · Rotate the load lever to fully open position. -
Page 16: Installing Memory Modules
1. To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/ heatsink supplied. The form and size of fan/heatsink may also vary. 2. -
Page 17: Installation Procedure
Installation Procedure Refer to the following to install the memory modules. This motherboard supports unbuffered DDR3 SDRAM . Push the latches on each side of the DIMM slot down. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they can only be installed correctly. -
Page 18: Expansion Slots
Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system. - Page 19 Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
-
Page 20: Connecting Optional Devices
Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: F_AUDIO: Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone and line- out ports for easier access. Signal Name Signal Name PORT 1L AUD_GND PORT 1R... - Page 21 F_USB1~2(USB 2.0): Front Panel USB 2.0 headers The motherboard has two USB 2.0 headers supporting four USB 2.0 ports. Addition- ally, some computer cases have USB 2.0 ports at the front of the case. If you have this kind of case, use auxiliary USB 2.0 connector to connect the front-mounted ports to the motherboard.
- Page 22 SPDIFO: SPDIF out header This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector. Signal Name SPDIFOUT COM: Onboard serial port header Connect a serial port extension bracket to this header to add a serial port to your system.
-
Page 23: Installing A Sata Hard Drive
Installing a SATA Hard Drive This section describes how to install SATA devices such as a hard disk drive and a CD- ROM drive. About SATA Connectors Your motherboard features four SATA 3.0 Gb/s connectors supporting a total of four drives. -
Page 24: Connecting I/O Devices
Connecting I/O Devices The backplane of the motherboard has the following I/O ports: DVI (Optional) PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Connect an RJ-45 jack to the LAN port to connect your LAN Port computer to the Network. -
Page 25: Connecting Case Components
Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: Connect the CPU cooling fan cable to CPU_FAN. Connect the system cooling fan connector to SYS_FAN. Connect the power cooling fan connector to PWR_FAN. Connect the case switches and indicator LEDs to the F_PANEL. - Page 26 Connecting 4-pin power cable The ATX12V4P power connector is used to provide power to the CPU. When installing 4-pin power cable, the latches of power cable and the ATX12V4P match perfectly. 4-pin power cable CPU_FAN: CPU cooling FAN Power Connector Signal Name Function System Ground...
- Page 27 PWR_FAN: FAN Power Connector Signal Name Function System Ground +12V Power +12V Sense Sensor SPK: Internal speaker Signal Name Signal ATX12V: ATX 12V Power Connector Signal Name Ground Ground +12V +12V Make sure to connect a 4-pin ATX power cable to ATX4P; otherwise, the system will be unstable.
-
Page 28: Front Panel Header
Front Panel Header The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information: Signal Function Signal Function HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+) HD_LED_N Hard disk LED(- ) FP PWR/SLP *MSG LED(-) -
Page 29: Using Bios
Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. -
Page 30: Resetting The Default Cmos Values
Press the delete key to access BIOS Setup Utility. Resetting the Default CMOS Values When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values. -
Page 31: Bios Navigation Key
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a icon . The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings. -
Page 32: Main Menu
Advanced Select the advanced icon and press <Enter> or double click the left key of the mouse to display the the following screen. Main Menu This menu shows the information of BIOS and enables you to set the system language, date and time. Main Advanced Chipset... -
Page 33: Advanced Menu
Advanced Menu The Advanced menu items allow you to change the settings for the CPU and other system. Main Advanced Chipset M.I.B III Boot Security Exit Legacy OpROM Support Enabled or Disabled Boot Launch PXE OpROM Disabled Option for Legacy Network Launch Storage OpROM Enabled Devices. -
Page 34: Lan Configuration
LAN Configuration The item in the menu shows the LAN-related information that the BIOS automatically detects. Main Advanced Chipset M.I.B III Boot Security Exit LAN Configuration Enabled/Disabled Onboard LAN 1 Controller Onboard LAN Controller Enabled : Select Screen /Click: Select Item Enter/Dbl Click : Select +/- : Change Opt. -
Page 35: Pc Health Status
PC Health Status On motherboards support hardware monitoring, this item lets you monitor the paeameters for critical voltages, temperatures and fan speeds. Main Advanced Chipset M.I.B III Boot Security Exit PC Health Status Smart Fan Function CPU Fan Speed 3013 RPM CPU Voltage 1.176V AXG Voltage... - Page 36 Smart Fan start PWM value (180) This item is used to set the start PWM value of the smart fan. Smart Fan start PWM TEMP(-) (30) This item is used to set the start temperature of the smart fan. DeltaT (3) This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works.
-
Page 37: Power Management Setup
Power Management Setup This page sets up some parameters for system power management operation. Main Advanced Chipset M.I.B III Boot Security Exit Power Management Setup About Resume by Ring Resume By Ring Disabled Resume By PME Disabled Resume By USB 1.x/2.0 (S3) Disabled Resume By PS2 KB (S3) Disabled... -
Page 38: Acpi Configuration
ACPI Configuration The item in the menu shows the highest ACPI sleep state when the system enters suspend. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset M.I.B III Boot Security Exit ACPI Settings Select the highest ACPI sleep state the system ACPI Sleep State S3 (Suspend to RAM) -
Page 39: Cpu Configuration
CPU Configuration The item in the menu shows the CPU. Main Advanced Chipset M.I.B III Boot Security Exit CPU Configuration Number of cores to enable in each processor package. Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz EMT64 Supported Processor Speed 3300 MHz Processor Stepping 206a6 Microcode Revision... - Page 40 Execute Disable Bit (Enabled) This item allows the processor to classify areas in memory by where application codecan execute and where it cannot. When a malicious worm attempts to insert code inthe buffer, the processor disables code execution, preventing damage or worm propa-gation.
-
Page 41: Sata Configuration
SATA Configuration Use this item to show the mode of serial ATA configuration options. Main Advanced Chipset M.I.B III Boot Security Exit SATA Configuration Determines how SATA controller(s) operate. SATA Mode IDE Mode SATA Port1 Not Present SATA Port2 Not Present : Select Screen /Click: Select Item SATA Port3... -
Page 42: Usb Configuration
USB Configuration Use this item to show the information of USB configuration. Main Advanced Chipset M.I.B III Boot Security Exit USB Configuration USB Support Parameters All USB Devices Enabled Legacy USB Support Enabled : Select Screen /Click: Select Item Enter/Dbl Click : Select +/- : Change Opt. -
Page 43: Super Io Configuration
Super IO Configuration Use this item to show the information of Super IO configuration. Main Advanced Chipset M.I.B III Boot Security Exit Super IO Configuration Set Parameters of Serial Port 0 (COMA) Super IO Chip IT8728 Serial Port 0 Configuration Parallel Port Configuration : Select Screen /Click: Select Item... - Page 44 Parallel Port Configuration Scroll to this item and press <Enter> to view the following screen: Main Advanced Chipset M.I.B III Boot Security Exit Enabled or Diabled Parallel Port Configuration Parallel Port (LPT/LPTE) Parallel Port Enabled Device Settings IO=378h; IRQ=5; Change Settings Auto : Select Screen Device Mode...
-
Page 45: Chipset Menu
Chipset Menu The chipset menu items allow you to change the settings for the North Bridge chipset, South Bridge chipset and other system. Main Advanced Chipset M.I.B III Boot Security Exit System Agent Configuration System Agent (SA) PCH Configuration Parameters Me Configuration : Select Screen /Click: Select Item... - Page 46 IGD Multi-Monitor (Disabled) This item enables or disables IGD (Internal Graphics device) multi-monitor. Press <Esc> to return to the Chipset Menu page. Multi-Monitor technology Multi-Monitor technology can help you to increase the area available for programs running on a single computer system through using multiple display devices. It is not only to increase larger screen viewing but aslo to improving personal productivity.
- Page 47 Step 2. Install all the drivers of PCI-Express graphic cards. Click the Browse CD item, then appears the following screen. Select the driver you want to install(e.g NVIDIA GeForce 8400 GS(Microsoft Corporation-WDDM v1.1)) and double click Step 3. Enable IGD Multi-Monitor from BIOS. In the following BIOS screen, please set IGD Multi-Monitor to [Enabled].
- Page 48 Step 4. Change the appearance of your displays under Windows 7. 1. Enter the Control Panel menu, select the Display in the All Control Panel Items and click the Screen Resolution, then appears the following screen. Show the path of the setting location Display devices Search Control Panel Control Panel...
- Page 49 Search Control Panel Control Panel All Control Panel Items Display Screen Resolution Change the apprearance of your displays Detect Identify Display: 4. AL1717 Resolution: 1920 x 1200 (recommended) Orientation: Landscape Multiple displays: Disconnect this display You must select Apply before making additional changes. Make this my main display Advance settings Make text and other items larger or smaller...
- Page 50 PCH Configuration Scroll to this item and press <Enter> to view the following screen. Main Advanced Chipset M.I.B III Boot Security Exit PCH Configuration Select AC power state when power is re-applied after Restore AC Power Loss Power Off a power failure. Audio Configuration Azalia HD Audio Enabled...
- Page 51 ME Configuration Scroll to this item and press <Enter> to view the following screen. Main Advanced Chipset M.I.B III Boot Security Exit Management Engine Technology Configuration ME FW Version 8.0.2.1410 : Select Screen /Click: Select Item Enter/Dbl Click : Select +/- : Change Opt.
-
Page 52: M.i.b Iii (Mb Intelligent Bios Iii) Menu
M.I.B III (MB Intelligent BIOS III) Menu This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system. Main Advanced Chipset... - Page 53 Integrated Clock Chip Configuration Scroll to this item to view the following screen: Main Advanced Chipset M.I.B III Boot Security Exit CPU OverClocking Configuration Enhanced Intel SpeedStep Technology CPU Frequency(1/100 MHz) 10000 CPU Ratio Enhanced Intel SpeedStep Technology Enabled Turbo Mode Enabled Internal PLL OverVoltage Disabled...
- Page 54 Long Duration Maintained (10) Use this item to control the time window over PL1 value should be maintained. This is for Turbo mode. Short Duration Power Limit Override (1680) Intel(R) Turbo Boost Technology will use this power limit for a very short duration. After that, the long duration power limit will be honored.
- Page 55 RAS# Active Time(tRAS) (24) This item specifies the RAS# active time. Write Recovery Time(tWR) (10) This item specifies the write recovery time. Row Refresh Cycle Time(tRFC) (74) This item specifies the row refresh cycle time. Active to Active Delay(tRRD) (4) This item controls the active bank x to active bank y in memory clock cycles.
- Page 56 B.O.M.P Technology (Enabled) This item allows users to enable or disable B.O.M.P technology. This function can run safe setting to setup menu when system boot fail 3 times. Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots. Spread Spectrum (Enabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.
-
Page 57: Boot Menu
Boot Menu This page enables you to set the keyboard NumLock state. Main Advanced Chipset M.I.B III Boot Security Exit Boot Configuration Specifies the Boot Device Priority sequence from Bootup NumLock State available Hard Drives. Set Boot Priority 1st Boot Hard Disk 2nd Boot CD/DVD... -
Page 58: Security Menu
Network Device Priorities (Press Enter) This item enables you to specify the sequence of loading the operating system from the installing network devices. UEFI Boot Drive Priorities (Press Enter) This item enables you to specify the sequence of loading the operating system from the installing UEFI Boot drives. -
Page 59: Exit Menu
Exit Menu This page enables you to exit system setup after saving or without saving the changes. Main Advanced Chipset M.I.B III Boot Security Exit Back to EZ Mode Go back to EZ Mode Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset : Select Screen... - Page 60 Boot Override Use this item to select the boot device. Using BIOS...
-
Page 61: Updating The Bios
Updating the BIOS You can download and install updated BIOS for this motherboard from the manufacturer’s Website. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs. Install new BIOS as follows: If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing. - Page 62 Memo Using BIOS...
-
Page 63: Using The Motherboard Software
Chapter 4 Using the Motherboard Software About the Software DVD-ROM/CD-ROM The support software DVD-ROM/CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. -
Page 64: Running Setup
Drivers Click the Setup button to run the software installation program. Setup Select from the menu which software you want to install. Click the Utilities button to display the application software and Utilities other software utilities that are available on the disk. Select the sofware you want to install then follow installation procedure. - Page 65 Click Next. The following screen appears: Check the box next to the items you want to install. The default options are recom- mended. Click Next run the Installation Wizard. An item installation screen appears: Follow the instructions on the screen to install the items. Drivers and software are automatically installed in sequence.
-
Page 66: Manual Installation
Windows Vista/7 will appear below UAC (User Account Control) message after the system restart. You must select “Allow” to install the next driver. Continue this process to complete the drivers installation. Manual Installation Insert the disk in the DVD-ROM/CD-ROM drive and locate the PATH.DOC file in the root directory. -
Page 67: Intel Matrix Storage Manager Raid Configurations
Chapter 5 ® Intel Matrix Storage Manager RAID Configuration ® The Intel Matrix Storage Manager allows you to configure RAID 0, and 1 sets on the external Serial ATA hard disk drives. Before creating a RAID set Prepare the following items: One SATA HDD. -
Page 68: Entering Intel ® Matrix Storage Manager Raid Bios Utility
® Entering Intel Matrix Storage Manager RAID BIOS utility ® During POST, press <Ctrl-I> to enter the Intel Matrix Storage Manager RAID BIOS menu. ® The main Intel Matrix Storage Manager RAID BIOS menu appears. Use the arrow keys to move the color bar and navigate through the items. ®... -
Page 69: Creating A Raid Set
Creating a RAID set ® In the main Intel Matrix Storage Manager RAID BIOS menu, highlight Create RAID Volume using the up/down arrow key then press <Enter>. When the RAID Level item is highlighted, use the up/down arrow key to select the RAID set that you want to create. - Page 70 When done, press <Enter> to confirm the creation of the RAID set. A dialogue box appears to confirm the action. Press <Y> to confirm; other- wise, press <N>. Pressing <Y> deletes all the data in the HDDs. The following screen appears, displaying the relevant information about the RAID set you created.
-
Page 71: Deleting A Raid Set
Deleting a RAID set ® In the main Intel Matrix Storage Manager RAID BIOS menu, highlight Delete RAID Volume using the up/down arrow key then press <Enter>. Use the space bar to select the RAID set you want to delete. Press the <Del>... -
Page 72: Resetting Disks To Non-Raid
Resetting disks to Non-RAID An HDD that has been previously configured as part of another RAID set in another platform is called a broken RAID HDD. When you install a broken RAID HDD, you cannot select this disk when configuring a RAID ®... -
Page 73: Trouble Shooting
Chapter 6 Trouble Shooting Start up problems during assembly After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. -
Page 74: Start Up Problems After Prolong Use
2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan. Start up problems after prolong use After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. - Page 76 Memo...