Weed Eater TE475 Instruction Manual page 3

CUTTING
SAFETY
_ WARNING:
Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled h_ line, Hard objects
can damage the trimmer head and be thrown
causing serious injury.
• Use only for trimming, scalping, mowing,
edging and sweeping, Do not use for prun-
ing or hedge trimmh_g.
• Keep firm footing and balance. Do not over-
reach.
• Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious bums.
• Out from your right to your left. Cutting on left
side of the shield will throw debris away from
the operator.
• Use only in daylight or good artificial light.
• Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
• Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
• Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbure-
tor by starting the engine and letting it run until
it stops.
• Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
• Store unit so line fimiter blade cannot acciden-
tally cause injury. The unit can be hung by the
shaft.
• Store unit out of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnor-
mal sweflings. Prolonged use in cold weather
has been linked to blood vessel damage in
ofl_erwise healthy people, if symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this too] and seek medical attention, An
anti-vibration system does not guarantee the
avoidance of these problems, Users who oper-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark ar-
resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S, forest
land and the states of California, idaho, Maine,
Minnesota, New Jersey, Oregon, and Washing-
ton require by law that many internal combus-
tion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining fl_e operating condition of these
parts. Failure to do so is a violation of the taw.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
vice. After 50 hours of use, we recommend that
your muffler be serviced or replaced by your au-
thorized service dealer.
_IWARNING:
If received assembled,
repeat all steps to ensure your unit is properly
assembled and atl fasteners are secure,
Examine parts for damage. Do not use dam-
aged parts.
NOTE: if you need assistance or find parts
missing or damaged, carl 1-800-554-6723,
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuet or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer,
ADJUSTING THE ASSIST HANDLE
1. Loosen wing nut on handle.
2. Pivot the handle to a comfortable position;
retighten wing nut,
Wing Nut
Groove
ATTACHING SHIELD
,_ WARNING:
The shield must be prop-
erly instaIled. The shietd provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
4. Securely tighten wing nut onto bolt.
Shield Slot
PIVOT
Bracket
Line Limiter
Blade
Nut