LG 47LB1DA Owner's Manual page 115

DataS:
m
z
O
X
All data are transmitted by Hexadecimal code
lwoiOne part Channel: 6th bit
This bit is used in a cable-ready system.
Using physical channek 5th bit
If the channel band is NTSC air or NTSC cable, channd
tuning can be done by only physical channel, tn this
case, using physical channel bit must be low(O).
gut if the channel band is ATSC air or ATSC cable, there
are two cases that physical channel enable or disable.
if the physka[ channel sending is meaningful, you should
set this bit low(O). If the physical channel sending is
meaningless, you should set this bit high(1 ),
Example)
1_.Analog channel: NTSC cable, channel number(SS),
main picture Command: ma 00 25 xx xx xx xx 01
attribute(0x0] ): main picture, two part(it's not
mandatory), using physical channel, NTSC cable "xx'
data: don't care major and minor channel number in
case analog channd tuning.
2. Digital channel: ATSC aig channel number(don't know
physical channel, major(S0), minor(S)), sub picture
Command: ma 00 xx 00 1E 00 03 A2
attrlbute(0xA2): sub picture, two part not using
physical channel ATSC air _x× _ data: don't care analog
channel number in case digital channel tuning.
3. Digital channel: ATSC ai_ channel number(physi-
cal(20),major(20), mino_ (3)), sub picture Command:
ma O0 T4 O0 14 00 OS 82
aHribu_e('0xg2): sub pidu_e, two Dart. using physica
channel. A[SC am
Ackn¢_wfr_,d_men_a} [ _ Set tDJ [ _ [OK] IDataOJ [Data] [
IL;ata2_ [Data 51 _Data4} [x_ Ial [ ] [Set _D_
[ ] [NG t [DataO[ [x]
25. _annel Add/Del (Command: m b)
To add and delete the channels
T_._s_iss_o,, [m][b]/ ] Is_t [D]/ ] [Data] [ Crl
Data 0: Channel Delete Data 1 : Channel Add
A_Mii_,k*d#e_&#_ [b] [ ] [S&t ID]I[ ] [OK/NG] [Data1[×]
26. Key (Command: m c)
To send IR remote key code,
Tr_ns,_,isdo_ [m] H [ [ iS,at ID][ ] [Data[ [C_]s
Data Key {.ode; Refer to page 1t6.
A_k_oMed_emen_ [c] [ ] [Set ID'] [ ] [O_JNG] [Da_a] [x]
27. Input select(Command: x b) (Main Picture Input)
To select input sou_'ce for TV.
T_smisS_o_ 1_] [b] [] [Set: I D][ ] [Dat_] [ Cq
Data 00 : UT'V (Antenna)
Data 10 : Analog (Antenna)
Data 20 : AVl
Data 40 : Com_nent 1
Data 50 : RGB DTV
Da_ 90: HDMHiDV[
Da_ 01 : DTV (Cable)
Data 11 : Analog (Cable)
Data 21 : AV2
Data 4-'I : Component 2
Data 60 : RC;B PC
Data 91 HDM[2
Ack_owt_*dgeme_[b][ ][Set ID][ ] [OK/NG]
[Di_a] IX]
28. PIP Input Select(Comman& x y)
To adjust input source lot sub picture in PiP mode_
Tr_msmls@_n I×] [y] [] [Set ID] [ [ [Data] [Cr]
Data 00 : DTV (Antenna)
Data 01 : DTV (Cable)
Data 10 : Analog (Antenna)
Data ll : Analog (Cable)
Data 20 : AV1
Data 21 : AV2
Ack_oMedg_:_m_,r_t[y] II _Set ID] [ _ IOK/NG] [Data] [q
114