SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
5) CADTV : 01~135 Input Voltage 1) AC 100 ~ 240V 50/60Hz Market NORTH AMERICA Screen Size 47 inch Wide(1920 x 1080) 47LB5DF-UC 42 inch Wide(1920 x 1080) 42LB5DF-UC 37 inch Wide(1920 x 1080) 37LB5DF-UC Aspect Ratio 16:9 Tuning System...
Page 7
5. Chrominance & Luminance Specification Item Unit Remark White peak brightness cd/m 47LB5DF-UC cd/m 42LB5DF-UC cd/m 37LB5DF-UC Contrast ratio cd/m Brightness uniformity Full white Color coordinate 0.638 +/- 0.03 0.340 +/- 0.03 GREEN 0.279 +/- 0.03 0.611 +/- 0.03 BLUE 0.146...
Page 8
Peak & average Brightness & Contrast measure standard specification - White Peak brightness measure specification 1) In non-impressed condition, measure peak brightness displayable as much as possible LCD module. 2) Measuring instrument: CA-110 or a sort of Color Analyzer. 3) Pattern Generator : VG-828 or a sort of digital pattern generator (displayable Full White & 1/25 White Window pattern) 4) Measure condition - Test pattern: in center, 1/5(H)x1/5(V) of Window Pattern (white pattern in non-impressed condition) - SET condition : Contrast &...
Page 11
9. General specifications 9-1. 47" LCD MODULE Item Specification Unit Remark Active Screen Size 46.96 inches(1192.87mm) mm Outline dimension 1096.0(H)x640.0(V)x481(D) Pixel Pitch 0.5415x0.5415x RGB Pixel Format 1920 horiz by 1080 vert. RGB Stripe arrangement Color Depth 8-bit / 16.7M Color Luminance, White 550 cd/m2 Power Consumption...
Page 12
10. Mechanical specification 10-1. 47LB5DF-UC Item Content Unit Remark Product Widt(W) Length(D) Height(H) Dimension Before Packing 1144.5 825.6 With Stant After Packing 1230 Product Only SET 37.5 With BOX 44.7 10-2. 42LB5DF-UC Item Content Unit Remark Product Widt(W) Length(D) Height(H)
9. Customer Menu Setup (Shipment Condition) Item Condition Remark Input Mode TV02CH Volume Level Mute Aspect Ratio 16:9 Video EZ Picture Daylight Contrast Brightness Color Sharpness Tint Color-temperature Cool Auto(On) Advanced Cinema3:2 Mode(Off) Black Level(RF,HDMI=>Low),(AV=>High)( RGB-PC,Component=>Disable) Audio Audio Language EZ Sound Normal Balance Bass...
Page 14
ADJUSTMENT INSTRUCTION 1. Scope 4. Adjustment method using RS-232C These instructions are applied to all of the LCD TV, LA73A Adjust the 3 board adjustment items of 3 using the RS-232C Chassis. according to the "4.1.2 Adjustment order". 4-1. Necessary details before adjustment 2.
Page 15
Rev button O Check RS-232C operation In this case, first press the of Video Signal Press the Instart of adjustment R/C to enter the 7.Baud Rate Generator (Master), to generate the white pattern to be displayed menu and set the Baud Rate to 115200 to check the 232-C from the left.
Page 16
5.3 480i Comp1, 1080p Comp1/RGB adjustment 6. EDID(The Extended Display method Identification Data)/DDC (Display Data Channel) Download A. ADC 480i component1 adjustment - Check Component1 connected condition from the using device. 6.1 Introduction - (MSPG-925FA : (model :209 , pattern :65 ) This has been established by VESA and is the function B.
7. White Balance adjustment A. Connect the set according to the internal pattern or HDMI input in accordance with 4.3.2 measuring device connection diagram. B. Set the Baud Rate of RS-232C to 115200. It is set to 115200 7-1. Using device as default.