Advertisement
Available languages
Available languages
Power
Indicator
Container
Full
Set Humidity
Indicator
Display
Room
H umidity/Temp
Fan Speed
Display
Indicators
_MAY[A
G
Power
Pause
I houl
Power
Pause
Humidistat
Control
Feature
Adjustment
Controls
Operation
1.
Allow dehumidifier
to reach
room temperature.
2.
Press "Power"
button
to activate
unit.
Power
"On"
indicator
lights up and fan will run at low speed.
The
unit
is pre-set to maintain
a 60% relative
humidity
level.
3.
4.
If "Set Humidity"
level is lower than
the "Room"
humidity
level: the compressor
will start up and unit
will start dehumidification.
If "Set Humidity"
level is higher
than the "Room"
level:
the unit will continue
to run on low fan.
After operating
several days at the default
setting,
with
doors and windows
closed,
you may adjust
the "Set
Humidity"
to a slightly
lower percent
(drier air) or
higher
percent
(moist
air). If you would
like to adjust
the "Set Humidity"
humidity
level, press the "+" or "-"
to adjust
the humidistat
in 5% increments
between
30%
and 90%.
5.
The "Room"
display
will display
either
the relative
humidity
or temperature
of the room. The default
setting
is room humidity.
To display
the temperature
of
the room press the "Humidity/Temp"
button.
Press it
again
to go back to the humidity
level.
To display
the Temperature
in Centigrade:
hold
down
the "Humidity/Temp"
button
for S seconds.
To
empty
the
Container:
When
the condensate
water container
is full, the indicator
lights
up.
1.
Turn the power
off before
removing
container.
Wait 3
minutes
for any remaining
water to drain
into the
condensate
container.
2.
Tilt the container
forward
then
lift carefully
by the handle.
3.
Clean and gently
re-insert
the container.
Important: This water is not suitable for drinking.
Humidity/Temp
Fan _
...................
Humidity/Temperature
Fan speed
Display toggle
Control
Press the "Fan Speed"
button
if you would
like to
change
the fan speed from
"Low" to "High",
Use the
high speed to maintain
maximum
water removal. The lower
speed can be used when quieter operation
is desired.
Press "Pause"
button
to pause operation
of dehumidifier
for 1 hour.
6.
71
8,
9.
An automatic
overflow
switch
and Container
"Full"
indicator
light are provided
to turn the dehumidifier
off
before
the container
overflows.
When
the indicator
light on the control
panel
glows, the water container
must
be emptied.
If Set humidity
is set to 30% then unit
is in "continuous
run" mode.
While
in this mode the compressor
will
continuously
run regardless
of actual
room
Humidity.
If
not properly
monitored
this setting
could
cause excess energy
usage.
Note: A piece of tape is attached
to the container
to ensure
safe sh pp rig. Th s p ece of tape can be removed.
Handle
Condensate
Container
Filter
Cleaning
1. Turn tile power
off.
2. Use a vacuum
cleaner
attachment
or brush to clean the front
grille.
3. Remove
the filter by sliding
the filter out using the recessed "finger-tip"
tab.
3. To clean the filter, wash in warm,
soapy water,
rinse and shake dry.
Cleaning
is recommended
monthly,
or as conditions
require.
4. For cleaning
the water container,
and wash with
warm
soapy water.
Properuse andcare of your dehumidifierwill helpensure longer life of the unit. It is recommended to
annuallyinspectand cleanthe coilsandcondensatewater passages. E xpense of annualinspectionis the
consumers' r esponsibility.
2
Condensate
Drain
Filter
Advertisement
