Advertisement
bracket
for
rear
venting
d, Remove screws attaching
brackets to each side of blower.
Reposkion
brackets on blower
as
shown.Then
reinstall
screws.
e, Reinstall blower
in blower
box
with mouth of blower
pointing
out
open side of blower
box. Secure
blower to blower
box wkh 6
Phillips-head
screws.
NOTE: Square metal frame
attached to mouth of blower
must
be installed
for proper operation.
f, Attach metal cover from parts
bag over downwenfing
knockout in
blower
box. Remove rear knockout
cover on back of vent base.
g, Reconnect
blower wiring
cane.
Secure wiring
came in 2 black
plastic clips inside vent base.The
wiring
cable must be properly
secured in the 2 clips (see step b,}
Reattach blow, er box to downdraft
vent base vvkh 4 hex nuts.
Attach backdraft damper
over blower
box knockout vvkh 2
Phillips-head
screws.
m Remove the 2 Phillips-head
screws attaching the wiring
box
cover. Determine
which direction
(rear or down) electrical
connection
vv, i ll need to run from appliance
wiring
box. Knock out rear or lower
wiring
opening
in wiring
box.
Excessive
Weight Hazard
Use two or more people to move
and install downdraft vent.
Failure to do so can result in back
or other injury.
lore
insert downdraft
vent
into countertop
cutout.Two
people
are recommended
to support the
weight
of the downdraft
vent
during lifting.
Position downdraft
vent so it is centered
in cutout and
parallel to edge of cutout. Check
that downdraft
vent is level
vertically.Then
fasten lower
support legs to cabinet floor with
screws.
When
attaching
undercounter
bracket
to underside
of countertop,
make
sure
that
the
screw
bngth
wiU not
go
through
countertop
when
tightened.
11m
Attach one undercounter
bracket on front upper right
corner of downdraft
vent with slot
over vent mounting
hob and
flange against countertop.
Attach
other bracket to left side of
downdraft
vent. Carefully
drill
starter hobs through
undercounter
mounting
brackets
into underside
of countertop.
insert appropriate
length screws
into hobs
and tighten
brackets to
countertop.
Ebctrical
Shock Hazard
Disconnect
power before
making electrical
connections.
Connect
ground wire to green
ground screw in terminam box.
Failure to do so can result in
death or ebctricaI
shock.
green
ground
screw
wiring -'/
box
conduit
connector
12m
Remove
required
knockout
and install
conduit
connector.
Feed the power
supply
cane
through
the conduit
connector
and into the wiring
box.
Connect
the white
wires
together
with
a twist-on
wire
connector.
Connect
the black wires
together
with
a twist-on
wire
connector.
Attach
the green
(or green
and
yellow)
ground
wire to eyelet
with
green
ground
screw.Tighten
the
conduit
connector
damp
screws.
Reattach
the wiring
box cover.
microswitches
behind filters.
ON/OFF
button
to
bbwer
eontro_
_fHter
or filters
knob
depending
on
\
mode_
end cap
13m
Turn power supply on.
Push and hold for a few' seconds
the button on the top of the
downdraft
vent. Retractable
section
of downdraft
vent will rise and
blower
will start. Position the top
trim over the retractable
section
and snap trim into place.
14m
Turn the control knob on
side of vent to check the operation
and speed of blower.
if blower does not operate:
o Check that filter or filters are
pressed in as far as they will go.
o Check that circuit breaker is not
tripped
or house fuse blown.
o Disconnect
power source and
check that wire connections
have
been made correctly.
Advertisement
