Advertisement
IOta
insert retractable
downdraft
vent into countertop
cutout.Two
people are
vent box
recommended
to support the
knockout
weight
of the downdraft
vent
during lifting.
Position downdraft
vent so it is centered in cutout and
parallel to edge of cutout, Check
that downdraft
vent is vertical.Then
attach lower support
legs to cabinet
green
floor wkh screws,
wire
/
When
attaching
undercounter
bracket
to underside
of countertop,
make
sure
that
the
screw
length
will
not
go
through
countertop
when
tightened,
1 m Attach one undercounter
mounting
bracket on front upper
right corner of downdraft
vent
with slot over vent mounting
hole
and flange against countertop.
Attach other bracket to left side of
downdraft
vent. Carefully
drill
starter hobs through
undercounter
mounting
brackets
into underside
of countertop.
insert appropriate
length screws
into holes and tighten
brackets to
countertop.
Electricam Shock Hazard
Disconnect
power before
making electricam connections.
Connect
ground wire to green
ground screw in terminaI
box.
Failure to do so can result in
death or electrical
shock.
...wiring
box
cover
green
ground
screw
connector
2
m Feed the power supply
cable through
the conduit
connector
and into wiring
box.
Connect the white wires together
with a twist-on
wire connector.
Connect the black wires together
with a twist-on
wire connector.
Attach the green (or green and
yellow) ground
wire to eyelet with
green ground
screw and tighten
screw. Replace wiring
box cover.
green
screw
-- green
j
ground
/
wire
/
/\
exterior-mounted
vent motor wiring
m Remove vent box
knockout and install conduit
connector.
Feed exterior-mounted
vent motor
wiring
through
conduit connector.
Do not wire the exterior vent
motor black and white wires into
the wiring
box.Wires
must be
connected
as shown.
Connect the
white wires together
with a twist-
on wire connector.
Connect the
black wires together
with a twist-
on connector.
Attach ground wire to eyelet with
green ground
screw and tighten
screw.
Tighten conduit
connector
clamp
screw's.
microswitehes
behind filters.
depending
on
\
mode_
end cap
14_
Turn power supply on.
Push and hold for a few seconds
the button on the top of the
dovvndraft vent. Retractable
section of downdraft
vent will rise
and blower will start. Position the
top trim over the retractable
section and snap trim into place.
5
m Turn the control knob on
side of vent to check the
operation
and speed of blower.
if blower
does not operate:
o Check that filter or filters are
pressed in as far as they will go.
o Check that circuit
breaker is not
tripped
or house fuse blown.
o Disconnect
power source and
check that wire connections
have been made correctly.
16m
Connect vent to blower.
Position vent to avoid wall studs
and floor joists. Complete
all vent
work.
Use duct tape to seal all
joints.
Vertical vent for walP
mounted
installations
should pitch
down slightly
toward
the vent to
allow moisture
to run outside.
17_
Install
cooktop
according
to manufacturer's
instructions.
Check that
rear of cooktop
overlaps
edge of retractable
downdraft
vent
by 3/8" (9.5 ram).
To get the most
efficient
use from your
new
retractable
downdraft
vent,
read the Use and Care
information
section
on
page
12.
Keep Installation
instructions
and Use and Care
information
ctose
by for
easy reference.
11
Advertisement
