Table of Contents
Advertisement
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 160°F (71°0) for 10 minutes. Sani Rinse adds
heat and time to the cycle. In the Normal cycle, this high-
temperature
rinse sanitizes your dishes and glassware in
accordance
with the NSF International
Protocol for Sanitization
and Cleaning Performance
of Household Spray-Type
Dishwashers (1997).
Sani
Rinse
NOTE: Sani Rinse is an option with the Heavy and Normal cycles.
Energy Saver Dry
Select this option to dry dishes without heat and save energy.
Energy Saver Dry is useful when loads contain plastic dinnerware
that may be sensitive to high temperatures.
Energy
Saver
The dishes take longer to dry and some spotting can occur. For
best drying, use a liquid rinse aid. Some items (such as plastics)
may need towel drying.
NOTE: Rinse Only automatically
uses this option. Energy Saver
Dry is an option with all other cycles.
Control
Lock
Use Control Lock to prevent your dishwasher
from accidentally
being turned on. Use Control Lock, also, to prevent accidental
cycle or option changes during a cycle.
Control
Lock
When CONTROL LOCK is lit, all buttons are disabled.
NOTES:
•
The dishwasher door can be opened while the controls are
locked.
•
You can turn on the Lock while the dishwasher
is running.
To turn on the Lock
Press and hold
Energy
Saver
for 4 seconds. CONTROL LOCK glows.
If you press any pad while your dishwasher
is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold ENERGY SAVER DRY for 4 seconds. The light
turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
oft-peak hours.
To delay the start
1. Close the door.
2.
Select a wash cycle and options.
Press DELAY HOURS 1 time for a 2-hour delay, 2 times for a
4-hour delay, or 3 times for an 8-hour delay start.
2
4
8
Delay
Hours
The number glows above Delay Hours. The dishwasher starts
the cycle in the selected number of hours.
3.
Press START.
NOTE: To cancel the delay, press DELAY HOURS until no number
is lit or press START.
IMPORTANT:
•
Operate your dishwasher only when you are at home.
•
If your home is equipped with a water softener, do not start
the dishwasher during the regeneration of the softener.
Follow the progress of your dishwasher with the Status
indicators.
I
o
o
o
o
o
o
Sensing/ Wash
Water
Rinse
Dry
Clean Sanitized
Soak
Heatin 8
Sensing/Soak
Your dishwasher senses the soil level on the dishes. Soil level
determines the length of some cycles, the amount of heat or
water added, and the cycle needed for the load. Soaks help
loosen soils on the dishes.
SENSING/SOAK
glows during the sensing and soak parts of the
cycle. Wash action continues while sensing occurs. Wash action
pauses during a soak.
Water
Heating
WATER HEATING glows, and the cycle progression pauses,
whenever water is heated to a set temperature
during a cycle.
Wash or rinse action continues as the water heats.
Clean
CLEAN glows when a cycle is finished. The light turns off when
you open and close the door or press Cancel/Drain.
Sanitized
If you select the Sani Rinse option, SANITIZED glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted or the incoming water
temperature
is too low. The light goes off when you open and
close the door.
13
Advertisement
Table of Contents
