Exmark Standon 4500-435 Operator's Manual
  1. Manuals
  2. Brands
  3. Exmark Manuals
  4. Lawn Mower
  5. Standon 4500-435
  6. Operator's manual
Exmark Standon 4500-435 Operator's Manual

Exmark Standon 4500-435 Operator's Manual

Exmark mfg. co. inc. zero-turn riding mower operator's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
STANDON
For Serial Nos.
790,000 & Higher
Part No. 4500-435 Rev. A

Advertisement

Table of Contents
loading

Related Manuals for Exmark Standon 4500-435

Summary of Contents for Exmark Standon 4500-435

  • Page 1 STANDON For Serial Nos. 790,000 & Higher Part No. 4500-435 Rev. A...
  • Page 2 Exmark reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products manufactured previously. Exmark, or its distributors and dealers, accept no responsibility for variations which may be...

  • Page 3: Introduction

    All Exmark parts are thoroughly tested and inspected before leaving the factory, however, attention is required on your part if you are to obtain the fullest measure of satisfaction and performance.

  • Page 4: Table Of Contents

    Contents Introduction ... 3 Safety ... 5 Safety Alert Symbol ... 5 Safe Operating Practices ... 5 Safety and Instructional Decals ... 7 Specifications ... 8 Model Numbers ... 8 Dimensions... 8 Tire ... 8 Setup ... 9 Assembly Diagram ... 9 Installing the StandOn Rider to Mower...

  • Page 5: Safety

    • Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use on machines approved by Exmark. • Wear appropriate clothing including safety glasses, substantial footwear, long trousers, and hearing protection. Do Not operate when barefoot or when wearing open sandals.

  • Page 6: Maintenance And Storage

    Safety DANGER Operating on wet grass or steep slopes can cause sliding and loss of control. Loss of control and/or loss of operator’s footing could result in a fall with an arm or leg getting under the mower or engine deck which may result in serious injury, death or drowning.

  • Page 7: Safety And Instructional Decals

    1-303517 • New safety signs may be obtained from your authorized Exmark equipment dealer or distributor or from Exmark Mfg. Co. Inc. • Safety signs may be affixed by peeling off the backing to expose the adhesive surface. Apply only to a clean, dry surface. Smooth to remove any air bubbles.

  • Page 8: Specifications

    Specifications Specifications Model Numbers Serial Nos: 790,000 and Higher STANDON Dimensions Length Width Height 35.4 inches 18.5 inches 14.9 inches (89.9 cm) (47.0 cm) (37.9 cm) Tire Tread Semi-Pneumatic Smooth Tire For Operators over 250 lb it is recommended to use pneumatic tire assembly P/N 103-3798.

  • Page 9: Setup

    Setup Assembly Diagram Item Quantity Description Nut, Nyloc 3/8-16 Flg Plate, Back-Up Plate, Adapter Screw, HH 3/8-16 x 1 1/4 Asm, Frame Pull W/Decals Asm, Pull Arm W/Brgs Guard, Top Screw, HH 3/8–16 x 4 3/4 Nut, Hex Flg-Side Lock 3/8-16 Asm, Sulky Frame W/Decals Decals, Replacement (Turf Tracer and Viking Hydro Only)

  • Page 10: Installing The Standon Rider To Mower

    Setup Installing the StandOn Rider to Mower Mounting the Pull Frame 1. Locate the pull frame and two adapter plates. Install the pull frame to the adapter plates using four 3/8-16 x 1 1/4 inch hex capscrews and four 3/8-16 inch nyloc nuts as shown in Figure 4. G009397 Figure 4 1.
  • Page 11 Figure 7 1. Replacement decals e. Align the pull frame and adapter plate assembly to the rear surface of the engine deck. Measure the distance from the bottom of the pull frame to the ground. Choose the mount holes that will attain a distance approximately 8 inches (20 cm).
  • Page 12 Setup Figure 10 1. Pull arm assembly 3. Pull frame 2. Quick connect pins 2. Remove the 3/8-16 x 4 3/4 inch hex capscrew. spring disc washer, and 3/8-16 inch hex flange side lock nut from the pivot hub. 3. Locate the sulky frame assembly and align with the pull arm assembly.

  • Page 13: Operation

    Operation Note: Determine the left and right sides of the machine from the normal operating position. Pre-Start 1. Make sure you understand the controls, their locations, their functions, and their safety requirements. 2. Practice operating the machine without the StandOn until familiar with the controls. 3.

  • Page 14: Maintenance

    Maintenance Maintenance Note: Determine the left and right sides of the machine from the normal operating position. WARNING While maintenance or adjustments are being made, someone could start the engine. Accidental starting of the engine could seriously injure you or other bystanders. Remove the key from the ignition switch, engage parking brake, and pull the wire(s) off the spark plug(s) before you do any...

  • Page 15: Lubricate Caster Wheel Hubs

    6. Pack the bearings with a NGLI grade #1 multi-purpose grease. 7. Insert one bearing, one new seal into the wheel. Note: Seals (Exmark PN 103-0063) must be replaced. 8. If the axle assembly has had both spacer nuts removed (or broken loose), apply a thread locking adhesive to one spacer nut and thread onto the axle with the wrench flats facing outward.

  • Page 16: Adjustments

    Maintenance Adjustments Adapter Plate and Tire Adjustment Important: For optimal performance, the StandOn pull arm top surface should be horizontal to the ground surface. To obtain a horizontal pull arm, the adapter plates and the platform wheel can be repositioned (see Figure 14).

  • Page 18: Service Record

    Service Record Date: Description of Work Done: Service Done By:...
  • Page 20 SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONS MID-MOUNT RIDING ACCESSORIES AND OPTIONS CUSTOM RIDE SEAT SUSPENSION SYSTEM FULL SUSPENSION SEAT DECK LIFT ASSIST KIT HITCH KIT LIGHT KIT V POWER PORT MICRO-MULCH SYSTEM OUT-FRONT RIDING ACCESSORIES AND OPTIONS CUSTOM RIDE SEAT SUSPENSION SYSTEM...

This manual is also suitable for:

Standon

Table of Contents