JVC RX-778VBK Instructions Manual page 12

To tune in a preset station
On the front panel:
1. Turn SOURCE SELECTOR to
select the band
(FM or AM).
The last received station of the selected band
is tuned in.
2. Press TUNER PRESET.
3. Turn MULTI JOG until you find
the channel you want.
• ]_ming it clockwise increases the channel
numbers.
• ]_rning it counterclockwise decreases the
channel numbers.
TUNER PRESET
From the remote control:
FM/AM
1. Press FM/AM. (-2--_^
• Each time you press the button, the band
alternates between FM and AM.
2. Press the 10 keys to select a preset (]D
channel number.
Q Q
• For channel number 5, press 5 ............
• For channel number 15, press +10 then 5. @
• For channel number 20, press +10 then 10.._.
• For channel number 30, press +10, +10, _ "x_ )_
then 10.
Note:
When you use the 10 keys on the remote control, be sure that they
are activated for the tuner, not for the CD and others. (See page 41.)
I,-'_ F4"4"lh'_li_ m I=_511:_'4'_:'Rl'lffl _51"_._
When an FM stereo broadcast is hard to
receive or noisy
You can change the FM reception mode while receiving an FM
broadcast.
• You can store the FM reception mode for each preset station.
Press FM MODE on the front panel or FM MODE/MUI]NG on
the remote control.
• Each time you press the button, the FM reception mode alternates
between "AUTO" and "MONO?'
FM MODE
On the front panel
On the remote
AUTO: When a program is broadcasted in stereo, you will hear
stereo sound; when in monaural, you will hear
monaural sounds. This mode is also useful to suppress
static noise between stations. The MUTE AUTO
indicator lights up on the display.
MONO: Reception will be improved although you will lose the
stereo effect. In this mode, you will hear noise while
tuning into the stations. The MUTE AUTO indicator
goes off on the display.
18
Note:
When using the FM MODE/MUTING button on the remote control, be
sure that the 10 keys are activated for tuner, not for the CD and
others. (See page 41.)
You can assign a name of up to four characters to each preset
station. When a preset station is tuned in, its assigned name will
appear on the display.
Bet_re you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start fi-om step 1 again.
• You can use the following characters: Space, A Z, and 0 9.
On the front panel ONLY:
1. Tune in a preset station.
See the left.
2. Press TUNER/SEA MEMORY.
The preset channel number starts flashing for
about 10 seconds.
_
TUNER MEMORY
• If you turn MULTI JOG while the preset channel number is
flashing, you can change the preset channel numbeE
3. Press TUNER PRESET, while the
preset channel number is flashing.
The 5rst character position starts flashing.
i ..........
4. Turn MULTI JOG to select the
first character, while the first
character position is flashing.
'[ ,,,
_,_,_.........
TUNER PRESET
5. Press TUNER PRESET, while a
TUNERPREsEr
character you want is flashing.
The next character position starts flashing.
k./
I 'I i'%_4
IH .i= I!_[ .--. _, .......
6. Repeat steps 4 and 5 to enter up to lbur
characters.
7. Press TUNER/SEA MEMORY
while the last selected character is
flashing after you have assigned a
name.
TUNER MEMORY
To erase the input characters
Insert spaces using the same procedure described above.