Oven Cleaning - Frigidaire CFEB30S5GC4 Guide Manual

Oven Cleaning
Self-Clean Cycle
NOTE: Tile kitchen area should be well ventilated using an open window, ventilation fan or exhaust hood during the Self-
Clean or Speed Clean cycle. This will help eliminate the normal odors associated with tile Self-Cleanning cycles.
To Set the Controls for a Self-Clean or a Delayed Start Self-Clean:
(Note: If you do not want to start a Delayed Self-Clean Cycle, skip steps 2 & 3.)
1. Be sure the clock shows the correct time of day.
2. Pressthe START TIME pad.
3. Press and hold the UP ARROW pad to scroll to the time to start the delayed Self-Clean
cycle. Release the pad when the desired time is displayed.
4. Press the CLEAN pad (for a 3 hour cycle). "- -" appears in the display.
5. Press the UP OR DOWN ARROW pad once.
As soon as the controls are set, the motor driven lock will begin to close automatically
and the "Door Locked" indicator light will flash. DO NOT open the oven door while the
light is flashing (it takes about 15 seconds for the oven door to lock).
6. "CLn" will appear in the display during the Self-Clean cycle and the "Door Locked" light
will glow until the Self-Cleaning cycle is complete or cancelled and the oven temperature
has cooled.
Self-Clean Cycle time length (for models with the SELECT CLEAN pad)
For satisfactory results, use a 2 hour Self-Clean cycle for light soils and a 3 hour cycle for
average or a 4 hour cycle for heavy soils. NOTE: The kitchen area should
be well ventilated using an open window, ventilation fan or exhaust hood during the Self-
Clean cycle. This will help eliminate the normal odors associated with the Self-Clean cycle.
NOTE: A smoke eliminator in
the oven vent converts most of
the soil into a colorless vapor.
_ To avoid
possible burns use care when
opening the oven door after
the Self-Cleaning cycle. Stand
to the side of the oven when
opening the door to allow hot
air or steam to escape.
_DO
NOT fo roe
the oven door open. This can
damage the automatic door
locking system. Use caution
and avoid possible burns when
opening the door after the
Self-Cleaning cycle has
completed. The oven may still
be VERY HOT.
To Set the Controls for a Self-Clean Cycle or a Delayed Start Self-Clean Cycle:
(Note: If you do not want to start a Delayed Self-Clean Cycle, skip steps 2 & 3.)
1. Be sure the clock shows the correct time of day.
2. Press START TIME pad.
3. Press and hold the UP ARROW pad to scroll to the time to start the delayed Self-Clean cycle. Release the pad when the
desired time is displayed.
4. Press SELECT CLEAN pad. "- -" appears in the display.
5. Press the UP OR DOWN ARROW once. "3:00" appears in the display for a 3 hour cycle. To change to a 2 hour cycle
press DOWN ARROW. "2:00" appears in the display or to select a 4 hour cycle press UP ARROW. "4:00" appears in
the display. As soon as the controls are set, the motor driven lock will begin to close automatically and the "Door
Locked" indicator light will flash. DO NOT open the oven door while the light is flashing (it takes about 15 seconds for
the oven door to lock).
6. "CLn" will appear in the display during the Self-Clean cycle and the "Door Locked" light will glow until the Self-
Cleaning cycle is complete or cancelled and the oven temperature has cooled.
When the Self-Clean
Cycle is Completed:
1. The time of day or "End" will appear in the display and the "Clean" and "Door Locked" light will continue to glow.
2. Once the oven has cooled down for about 1 HOURand the "Door Locked" light has gone out, the oven door can be opened.
3. If "End" is in tile display and the Select Clean indicator light remains ON, press the CLEAR/OFF or STOP pad. The time
of day will appear in the display.
NOTE: When the oven is cool, wipe away any residue or powdered ash with a damp cloth or paper towel.
Stopping or Interrupting a Self-Cleaning Cycle
If it becomes necessary to stop or interrupt a Self-Cleaning cycle:
1. Pressthe CLEAR/OFF or STOP pad.
2. Once the oven has cooled down for about 1 HOURand the "Door Locked" light has gone out, the oven door can be opened.
:3. Restart the Self-Clean cycle once all conditions have been corrected.
9