Husqvarna 137 Instruction Manual page 4

Hearing Safety Hat
Protection
_ Eye
""_, i U.e _'" Protection
Snug
Fitting Heavy Duty
Clothing GIoves
Safety Safety Chaps
Shoes
• Wear protective gear. Always use steeFtoed
safety footwear with non-slip soles; snug-fit-
ting clothing; heavy-duty, non-slip gloves;
eye protection such as non-fogging, vented
goggles or face screen; an approved safety
hard hat; and sound barriers (ear plugs or
mufflers) to protect your hearing, Secure hair
above shoulder length.
• Always use approved hearing protection.
Regular users should have hearing
checked regularly as chain saw noise can
damage hearing. Long-term exposure to
noise can result in permanent hearing im-
pairment,
• Keep all parts of your body away from the
chain when the engine is running.
• Keep children, bystanders, and animals a
minimum of 30 feet (10 meters) away from
the work area. Do not aflow other people
or animals to be near the chain saw when
starting or operating the chain saw,
• Do not handle or operate a chain saw
when you are fatigued, ill, or upset, or if you
have taken alcohol, drugs, or medication.
You must be in good physical condition
and mentally alert. Chain saw work is
strenuous, if you have any condition that
might be aggravated by strenuous work,
check with your doctor before operating a
chain saw,
• Carefully plan your sawing operation in ad-
vance. Do not start cutting until you have a
clear work area, secure footing, and, if you
are felling trees, a planned retreat path,
OPERATE YOUR SAW SAFELY
• Do not operate a chain saw with one hand.
Serious injury to the operator, helpers, by-
standers or any combination of these per-
sons may result from one-handed opera-
tion, A chain saw is intended for
two-handed use.
• Operate the chain saw only in a welFventi-
lated outdoor area.
• Do not operate saw from a ladder or in a tree.
• Make sure the chain will not make contact
with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
• Do not put pressure on the saw at the end of
the cut, Applying pressure can cause you to
lose controI when the cut is completed and
may cause serious personal injury.
• Stop the engine before setting the saw
down,
• Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely and securely assembled, Always
replace bar, chain, hand guard, or chain
brake immediately if it becomes damaged,
broken or is otherwise removed.
• With the engine stopped, hand carry the
chain saw with the muffler away from your
body, and the guide bar and chain to the
rear, preferably covered with a scabbard,
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
• Haveallchainsawserviceperformed bya
qualified service dealer with the exception
of the items listed in the maintenance sec-
tion ofthis manual. For example, ifimprop-
er tools are used to remove or hotd the fly-
wheel when servicing the clutch, structural
damage to the flywheel can occur and
cause the flywheel to burst,
• Make certain the saw chain stops moving
when the throttle trigger is released, For
correction, refer to CARBURETOR AD-
JUSTMENTS,
• Never modify your saw in any way,
• Keep the handles dry, clean, and free of oil
or fuel mixture,
• Keep fuel and oil caps, screws, and fas-
teners securely tightened,
• Use only Husqvarna accessories and re-
placement parts as recommended.
HANDLE FUEL WITH CAUTION
• Do not smoke while handling fuel or while
operating the saw,
• Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
There should be no smoking, open flames,
or work that could cause sparks. Allow en-
gine to coot before refueling.
• Mix and pour fuel in an outdoor area on
bare ground; store fuel in a cool, dry, weII
ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up all fuel spills before starting saw.
• Move at least 10 feet (3 meters) from fuel-
ing site before starting engine.
• Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit,
• Store the unit and fuel in an area where fuel
vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.
KICKBACK
_L, WARNING:
Avoid kickback which
can result in serious injury. Kickback is the
backward, upward or sudden forward motion
of the guide bar occurring when the saw
chain near the upper tip of the guide bar con-
tacts any object such as a log or branch, or
when the wood closes in and pinches the
saw chain in the cut. Contacting a foreign ob-
ject in the wood can also result in loss of
chain saw control,
• Rotational Kickback can occur when the
moving chain contacts an object at the up-
per tip of the guide bar. This contact can